Kentec Electronics DNX-R-2F-K Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 42

Kentec Electronics DNX-R-2F-K Скачать руководство пользователя страница 32

Power supply monitoring

The DNX R-2F/FC module can

monitor the dual power supplies for either “out of limits”

operation or total failure. The events are automatically recorded for recovery on
request using additional

i

NS tools. A typical example of a configuration for monitoring

the auxiliary and backup battery power supplies is illustrated in Figure 17a.

This feature supports the tracking of CIE watchdog events if the auxiliary PSU being
monitored is disconnected during the watchdog event.

Figure 17a: Example of a configuration for monitoring the auxiliary and backup

battery power supplies

If a

single

power supply source is used (this practice is NOT recommended by

Kentec), the PSU connections need to be wired as indicated in Figure 17b to avoid the
fault LED flashing to indicate a PSU fault.

Figure 17b: PSU wiring for single power supply source

32

Man-1492

DNX-R-2F/FC-K

«
...
30
31
32
33
34
...
»

Содержание DNX-R-2F-K











































Отзывы:

Нет отзывов