Kentec Electronics DNX-R-2F-K Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 42

Kentec Electronics DNX-R-2F-K Скачать руководство пользователя страница 15

DIP-switch settings

Before accessing the internal DIP-switch and jumper settings: (sets 1, 2, 3, 4 & 5)

Prevent damage to internal electronics from electrostatic discharges (ESD) by
discharging your body to a grounding point (e.g. use of a wrist strap). For internal DIP
SWITCH setting information, refer to the DNX R-2F/FC Advanced User Manual.

The configuration setting for use with Kentec fire alarm panels has been simplified so
that you only need to set Rotary switch (Rot SW 1) and DIP Switch Set 6, (refer to
Figure 6) both of which are externally accessible. You should therefore not need to
open the product enclosure. The settings as presented in Tables 10 and 11.

After changing any DIP switch setting, it is essential that the power be turned
OFF and ON again for the setting changes to be recognized.

Figure 6: DIP-switches and Rotary switch

Switch settings for DNX R-2F/FC operation

The switch settings should only be altered by a competent user, who understands the
implications of changing each switch. Altering the switches could compromise the
functioning of the device if set incorrectly.

SW Set 6

ROT

SW 1

15

Man-1492

DNX-R-2F/FC-K

«
...
13
14
15
16
17
...
»

Содержание DNX-R-2F-K











































Отзывы:

Нет отзывов