Kentec Electronics DNX-R-2F-K Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 42

Kentec Electronics DNX-R-2F-K Скачать руководство пользователя страница 14

Figure 5: Node Display

Note

– if ALL of the IO PORT LEDs are OFF, then the DNX R-2F/FC is in

PASSIVE mode.

Features included in DNX R-2F/FC (module) and DNX R-2F/FC-UG
(upgrade)

Feature

DNX R-2F/FC

+ DNX R-2F/FC-UG

Passive mode of operation

✓

✓

Active mode of operation (basic mode)

✓

✓

Full optic fibre analysis with report generation in IVIEW

✓

✓

Analysis of signals entering the optic fibre network

✓

Signal interference profiling

✓

Power supply monitoring

✓

Third party Data flow monitoring across the network

✓

Table 9a: Supported Feature Set

SFP signing

All of the supplied SFP transceivers are signed to mark calibration with the
DNX R-2F/FC product and any non-signed transceivers must NOT be used with the
DNX R-2F/FC.

Any use of SFP transceivers with the product will void the warranty on the
product as it will affect the operation of the product.

If the SFP transceiver is NOT signed, the IO PORT 1 and 2 LED will flash in sync to
indicate an unsigned transceiver in PORT B and IO PORT 3 and 4 LEDs will flash in
sync for an unsigned SFP transceiver in PORT C.

14

Man-1492

DNX-R-2F/FC-K

«
...
12
13
14
15
16
...
»

Содержание DNX-R-2F-K











































Отзывы:

Нет отзывов