Kentec Electronics DNX-R-2F-K Скачать руководство пользователя страница 5

Страница: 5 / 42

Safety Control Drawing

Position

Description

Input / Output values

–

LC connector interface for fibre - PORT B

Data rate: 100 Mb/s

–

125 MBd.

Fibre drive distance:
M: Multi-mode - up to 2km

S: Single-mode

–

10 / 15 / 20 /

40 / 80km variants

M: 850nm / 1310nm
S: 1310 / 1550nm

BiDi: 1310 & 1550nm

–

LC connector interface for fibre - PORT B

–

LC connector interface for fibre - PORT C

–

LC connector interface for fibre - PORT C

Screen/Shield RS-485/ARCNET - PORT B or C

Umax = ± 5Vpk

Imax = ± 60 mA
Data rate:

4.8 to 115.2 kbit/s

In / Out / + line RS-485/ARCNET - PORT B or C

In / Out / - line RS-485/ARCNET - PORT B or C

Screen/Shield RS-485/ARCNET - PORT A1 (Panel IN Port)

In / Out / + line RS-485/ARCNET - PORT A1 (Panel IN Port)

In / Out / - line RS-485/ARCNET - PORT A1 (Panel IN Port)

Screen/Shield RS-485/ARCNET - PORT A2 (Panel OUT Port)

In / Out / + line RS-485/ARCNET - PORT A2 (Panel OUT Port)

In / Out / - line RS-485/ARCNET - PORT A2 (Panel OUT Port)

Table 3

DNX R-2F Configuration

DNX R-2FC Configuration

Figure 1

Table 4

Position

Description

Input / Output values

In / +Voltage A

Uin = (18

–

36): 24 VDC Nominal

Iin = 210 mA Rated at 24 VDC

In / Common

In / +Voltage B

In / Common

Earth connection

In & out / Relay contact (C - Common)

Uin = 30 VDC max
Iin = 2000 mA max, Pin = 60 W max

In & out / Relay contact (NC - Normally Closed)

In / Out / - line RS-485

–

IO Interface

Umax = ± 5Vpk
Imax = ± 60 mA

Data rate:
4.8 to 115.2 kbit/s

In / Out / + line RS-485

–

IO Interface

Screen/Shield RS-485

–

IO Interface

Man-1492

DNX-R-2F/FC-K

Содержание DNX-R-2F-K











































Результаты поиска

Содержание DNX-R-2F-K

Отзывы:

Kentec Electronics DNX-R-2F-K, Руководство пользователя, Страница: 5 / 42

Результаты поиска

Содержание DNX-R-2F-K

Отзывы: