Kentec Electronics DNX-R-2F-K Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 42

Kentec Electronics DNX-R-2F-K Скачать руководство пользователя страница 22

Configuration and Installation

The

DNX R-2F/FC

modules can be used in both the “Passive” and “Active” modes of

operation. The installation of the

i

NS should be executed in order of presentation.

C

onfiguration steps:

1)

Configure the local communication settings for each DNX R-2F/FC.

The communication settings are configured for the respective fire alarm panel by
setting the Rotary switch 1 in Table 11.

2)

Configure the Module as Master or

Slave (ONLY required for ACTIVE

Mode)

When using the DNX R-2F/FC modules in active mode, a master is required for
commissioning the network and managing the fault recovery procedure.
It is important that there is only a single (ONE) DNX R-2F/FC master per class A
ring or class B radial.
Adjust the Master/Slave selection on the device by setting or re-setting DIP
SWITCH 1 of set 6 as per selection in Table 10.

Master Module

Slave Module

Set 6

Set 6

3)

Selecting ACTIVE or PASSIVE Mode of operation local to a module

Setting the Mode local to the Module:
You can set the Mode of operation of the module by setting or re-setting DIP
SWITCH 4 of set 6 as per selection in Table 10.

Active Mode (DNA)

Passive Mode (DNP)

Set 6

Set 6

22

Man-1492

DNX-R-2F/FC-K

«
...
20
21
22
23
24
...
»

Содержание DNX-R-2F-K











































Отзывы:

Нет отзывов