Kaba Peaks Classic Скачать руководство пользователя страница 39

Страница: 39 / 92

Section 2 - 27

tio

6-pin 140

• brass plug

• alloy shell and control sleeve with patented plating and coating

• spring cover retains pins and springs

• 6840-00-3540 staking fixture and 6440-00-4001 staking tool required

• no forbidden or mandatory control combinations

• face of plug is key stop for longer core life

• This product uses a large diameter plug.

J series bottom pins required for A2 system pinning.

K series bottom pins required for A4 system pinning.

Uses:

6340-00-4012 timing pin

6800-00-2007 7-pin small format

interchangeable cores spring cover

6140-00-4002 C-ring plug retainer

Large Format Removable Cores for Sargent—8544/6540 Series

Install timing pin here.

top view of core

Timing pin engages slot

in sleeve to create

positive key pull stop

for control key.

uncombinated:

combinated:

8544-xx-1006

8544-xx-1206

140, 6 pin

6540-xx-1006

6540-xx-1206

140, 6 pin

6-pin 140

• brass plug

• alloy shell and control sleeve with patented plating and coating

• spring cover retains pins and springs

• 6440-00-3540 staking fixture and 6440-00-4001 staking tool required

• pins like original small format interchangeable cores; A2 system stacks to 26

• face of plug is key stop for longer core life

• 6440-00-2000 spring cover

• 6140-00-4002 C-ring plug retainer

uncombinated:

combinated:

8444-xx-1006

8444-xx-1206

140, 6 pin

6440-xx-1006

6440-xx-1206

140, 6 pin

NOTE:

Dedicated pin kit #6440-00-5002 required: Available for A2 system pinning only.

Uses:

6440-00-2000 spring cover

6140-00-4002 C-ring plug retainer

Large Format Removable Cores for Schlage—8444/6440 Series

Содержание Peaks Classic





























































































Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды

Kaba Peaks Classic, Техническое руководство

Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды