Kaba Peaks Classic Скачать руководство пользователя страница 90

Страница: 90 / 92

Assa Abloy

•

“YALE”

appears the latch face.

• All grade 1 & 2 product is key demountable.*

TOOLS:

• 3400 grade 1 knobs require a spanner wrench.

• 3400L grade 1 levers require an

" Allen wrench and an original Yale 5400L spanner wrench.

Section 5 - 10

Division of Ingersoll Rand

•

“SCHLAGE”

appears the latch face.

TOOLS:

• Spanner wrench is required for grade 1.

• Castlenut bushing wrench (included with new locks) is required to install AL grade 2 leversets,

but not to change the cyl in ders.

•

" pin punch for depressing retainer.

NOTES:

• Original S series tailpiece must be used in 8400-xx1099 or 3400-xx-1099 cylinder.

Schlage Lock Co.

Yale Security

Schlage

D series

H series

A, AL series

S series

E/B series

grade 1

grade 2

tubular

knobs & levers interconnected knobs & levers

levers

deadlocks/latches

retrofit type

KDH

Peaks Preferred 8400-xx-1099 8400-xx-1099 8400-xx-1099

8400-xx-1099

Peaks Classic

3400-xx-1099 3400-xx-1099 3400-xx-1099

3400-xx-1099

Yale 5400L

5400

6200 Monolock 5300L

5300

grade 1

grade 1 unit lock grade 2

grade 2

levers

knobs

preassembled

levers

knobs

retrofit type

KDH*

KDH

Peaks Preferred 8400-xx-1055 8400-xx-1054

8400-xx-1054

8400-xx-1095

8400-xx-1054

Peaks Classic

3400-xx-1055 3400-xx-1054

3400-xx-1054

3400-xx-1095

3400-xx-1054

*The original 5400 Augusta Lever was non-key demountable.

This lock was pro duced for only a few months and was re de signed to be key demountable.

Содержание Peaks Classic





























































































Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды

Kaba Peaks Classic, Техническое руководство

Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды