Kaba Peaks Classic Скачать руководство пользователя страница 87

Страница: 87 / 92

Section 5 - 7

lin

r I

lla

tio

Division of Ingersoll Rand

•

“FALCON”

appears on the latch face.

TOOLS:

• Spanner wrench is required for grade 1.

•

" pin punch for depressing retainer.

hole in

edge of rose

rose

Amityville, New York

•

“MARKS”

appears on the latch face.

• Grade 1 and 2 cylindrical locks can be prepped for small format interchangeable core.

• Current Marks deadbolts accept only 6-pin small format interchangeable core.

knob

Falcon Lock Co.

Marks USA

• 8400-xx-1095 is identical to 8400-xx-1099 and 3400-xx-1095 is identical to 3400-xx-1099, except for the

small diameter plug face required for Falcon dead locks and old style X series unit locks.

Falcon

LY series

X series

RU and X series

S series

D series

grade 1

grade 1 unit lock

grade 2

tubular

levers

knobs

preassembled

knobs

deadlocks/latches

retrofit type

KDH

Peaks Preferred

8400-xx-1099 8400-xx-1099 8400-xx-1099

8400-xx-1099

8400-xx-1095

Peaks Classic 3400-xx-1099 3400-xx-1099 3400-xx-1099

3400-xx-1099

3400-xx-1095

*with original Marks tailpieces

TOOLS:

• Marks spanner wrench (engages entire rose) is

required to install lockset, but not to change

cylinders.

Marks

195/295

180

170/270

110/120

130 Deadlocks

grade 1

grade 2

levers

knobs

levers

knobs

retrofit type

KDH

Peaks Preferred

8400-xx-1099* 8400-xx-1099* 8400-xx-1099* 8400-xx-1099*

8400-xx-1099*

Peaks Classic

3400-xx1099*

Содержание Peaks Classic





























































































Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды

Kaba Peaks Classic, Техническое руководство

Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды