Kaba Peaks Classic Скачать руководство пользователя страница 82

Страница: 82 / 92

Section 5 - 2

Identifying the Manufacturer

Logo

Brand

On Face

Notes

Arrow

yes

“AMEROCK” and other OEM names have been used.

Corbin

yes

Prior to the brand merger in 1993, the individual brand names “CORBIN” or

Russwin

“RUSSWIN” were used. The Emhart logo, a capital E with horizontal arrows

was used during Emhart’s ownership. Some older unit locks have no trademark.

Falcon

yes

Falcon LY series grade 1 levers were imported from the same

source as PDQ grade 1 levers and are sometimes confused.

LSDA

yes

Imported; house brand of the IDN companies.

Marks

yes

PDQ

maybe

Latches for these locks bear check marks in a circle

(sic),

and may be private labeled.

Products assembled in the U.S.A. are marked “PDQ”.

Sargent

yes

Product line numbers 6, 7, 8, 9, 10, 7600, etc. are stamped on the face.

eg., a latch face marked "8" indicates an 8 Line lock.

Schlage

yes

Same key-in-knob cylinder body used throughout cylindrical lock line.

Only the tailpiece shape and ori en ta tion vary.

Yale

yes

5-pin versus 6-pin

Older hardware may have 5-pin cylinders and no room in the handle to retrofit a 6-pin cylinder. Existing

operating keys can be misleading. For ex am ple, some contemporary hardware is pinned to 5-pin keys, even

though the cylinders have six pin chambers. This is re ferred to as “drilled 6, pinned 5”. Try a 6-pin key blank

in the cylinder. It will not seat fully in a 5-pin cylinder.

The face of the latch is the first indicator of manufacturer. Certain brands of latch bolts

and lock chassis are compatible. For example, occasionally an Arrow chassis will be

seen with a Schlage latch bolt. When the knob or lever is removed, the appearance of

the spindle cam, i.e., the cylindrical actuator into which the cylinder tailpiece fits, can be

used to identify the chassis.

Содержание Peaks Classic





























































































Результаты поиска

Содержание Peaks Classic

Отзывы:

Kaba Peaks Classic, Техническое руководство, Страница: 82 / 92

Результаты поиска

Содержание Peaks Classic

Отзывы: