Kaba Peaks Classic Скачать руководство пользователя страница 84

Страница: 84 / 92

Division of Yale Security

Assa Abloy

• Depending on the vintage,

“CORBIN”, “CORBIN RUSSWIN”, “EMHART”

, and

“RUSSWIN”

will all be seen

on latch faces.

• Corbin Russwin’s proprietary profile core can be retrofit with Peaks 8144/6140 Rcore.

Section 5 - 4

Corbin Russwin Architectural Hardware

TOOLS:

• Grade 1 levers CL3400 and CL3600, require #585F48 hex wrench for flanged nut on rose liner.

• Grade 1 knobs, CK4200, require spanner wrench and long nose Tru-Arc pliers.

• Replacement of pre-1972 cylinders requires purchase of Corbin Russwin cylinder driver #144F29.

Corbin Russwin Corbin

product

retrofit

Peaks Preferred

old no. old no.

Russwin (1993)

method

Peaks Classic

700

900

CL3200

grade 1 levers

KDH

8144 LFIC

6140 LFIC

CL3300

grade 1 levers

KDH

8400-xx-1099

3400-xx-1099

800

CL3400, CL3600

grade 1 levers

KDH

8400-xx-1099 or 8144 LFIC

3400-xx-1099 or 6140 LFIC

CL3800

grade 2 levers

KDH

8400-xx-1099 with OEM tailpiece

discontinued 9-97

3400-xx-1099 with OEM tailpiece

(replaced by CL3900)

CL3900

grade 2 levers

KDH

8400-xx-1055

3400-xx-1055

400

CK4200

grade 1 knobs

Non-KDH

8400-xx-1004 or 8144 LFIC

3400-xx-1099 or 6140 LFIC

6600

3400

CK4400

grade 2 knobs, import KDH/

Non-KDH

in development

300

500

UT5200

grade 1 unit locks

Non-KDH

8400-xx-1004 or 8144 LFIC

3400-xx-1099 or 6140 LFIC

Содержание Peaks Classic





























































































Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды

Kaba Peaks Classic, Техническое руководство

Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды