Kaba Peaks Classic Скачать руководство пользователя страница 57

Страница: 57 / 92

Section 3 - 13

tti

&
P

8244/6240 large format interchangeable core for Yale

The 8244/6240 large format interchangeable core have an A2 system pin stack total of 26.

Use 8244-xx-1006 or 6240-xx-1006 to retrofit Yale 1210.

8244 cores use the following components:

A2 system: A series bottom pins and B series top pins

A4 system: E series bottom pins and F series top pins

8800-00-3004 patent bottom pin

3800-00-3005 patent top pin

3800-00-4010 stainless steel tumbler springs

3425-00-2006 mortise/rim spring covers

6240 cores use the following components:

A2 system: A series bottom pins and B series top pins

A4 system: E series bottom pins and F series top pins

3800-00-3004 patent bottom pin

3800-00-3005 patent top pin

3800-00-4010 stainless steel tumbler springs

3425-00-2006 mortise/rim spring covers

Top load the core in the usual manner. Stake in 6840-00-3540 staking fixture.
• Work on a firm bench surface.

• Strike tools gently with a plastic or rawhide mallet.

• Do not use excessive force.

Pinning Interchangeable Cores

6340 large format interchangeable core for Medeco 32 Series

The 6340 large format interchangeable core have an A2 system pin stack total of 26. The

6340 series requires a timing pin, number 6340-00-4012, which must be installed during

pinning. Uncombinated cores do not contain the timing pin. They can be found in the

Peaks universal pin kits. Do not omit the timing pin. Omitting the timing pin will make it

difficult to install the core.

6340 cores use the following components:

A2 system: A series bottom pins and B series top pins

A4 system: E series bottom pins and F series top pins

6340-00-4012 timing pin

3800-00-3004 patent bottom pin

3800-00-3005 patent top pin

3800-00-4010 stainless steel tumbler springs

6800-00-2007 spring cover, 7-pin

Top load core in the usual manner. Install 3800-00-3004 patent bottom pin and 3800-00-3005 patent top pin in

the patent chamber. Use 3800-00-4010 stainless steel tumbler springs in all chambers.
The 6800-00-2007 7-pin small format interchangeable core spring cover is required to contain all the compo-

nents. Apply spring cover using Peaks core staking fixture and staking tool.

• Work on a firm bench surface.

• Strike tools gently with a plastic or rawhide mallet.

• Do not use excessive force.

Install timing pin here.

top view of core

Содержание Peaks Classic





























































































Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды

Kaba Peaks Classic, Техническое руководство

Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды