Kaba Peaks Classic Скачать руководство пользователя страница 38

Страница: 38 / 92

Section 2 - 26

NOTE:

Yale cores are not interchangeable across Yale’s product line. It must be determined

if you are replacing a Yale 1210, 6-pin core, or a Yale 1220, 7-pin core.

uncombinated:

combinated:

8244-xx-1006

8244-xx-1206

for Yale 1210 140, 6-pin

6240-xx-1006

6240-xx-1206

for Yale 1210 140, 6-pin

6240-xx-1007

6240-xx-1207

for Yale 1220 140, 7-pin

6-pin 140

• brass plug

• alloy shell and control sleeve with patented plating and coating

• spring cover retains pins and springs

• 6840-00-3540 staking fixture and 6440-00-4001 staking tool required

• does not require a special extended tip control blank

• face of plug is key stop for longer core life

• retrofits Medeco 31

Uses:

3425-00-2006 mortise/rim spring cover

6240-00-4002 C-ring plug retainer

Large Format Interchangeable Cores for Yale—8244/6240 Series

8244-xx-1006

6240-xx-1006

retrofits Yale 1210 in 6-pin housings ONLY

6240-xx-1007

retrofits Yale 1210 in 7-pin housings ONLY

6-pin 140

uncombinated:

combinated:

6340-xx-1006

6340-xx-1206

140, 6-pin

• brass plug

• alloy shell and control sleeve with patented plating and coating

• spring cover retains pins and springs

• 6840-00-3540 staking fixture and 6440-00-4001 staking tool required

• no forbidden or mandatory control combinations

• face of plug is key stop for longer core life

Uses:

6340-00-4012 timing pin

6340-00-4002 C-ring plug retainer

6800-00-2007 7-pin small format inter-

changeable core spring cover

Large Format Interchangeable Cores for Medeco 32—6340 Series

Содержание Peaks Classic





























































































Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды

Kaba Peaks Classic, Техническое руководство

Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды