Kaba Peaks Classic Скачать руководство пользователя страница 78

Страница: 78 / 92

Section 4 - 10

The TMK register logs all top master keys and control keys by system register number to prevent

duplication of systems.This type of register is kept by all manufacturers. Kaba maintains their

logs by keyway, parity pattern and system location.

Example of TMK Register

Mfr.

Key Section

TMK

Control

Parity

Location

Register #

Corbin

453263

Sys70

Toledo

A012

Dexter

12212

OEEOE

Medina

A102

Kaba

PEAKS-D

836152

EOEOOE

Parma

A016

Kaba

PEAKS-D

793063

957405

OOOEEO

Bay Village

A015

Kwikset

1063

41363

none

Rocky River

A035

Sargent

361794

363594

OEOOOE

Bay Village

A013

Adding small & large format interchangeable cores to a system of conventional cylinders

Small format interchangeable core/large format interchangeable core cylinders can usually be added to a

system of 140 conventional cylinders at any time. KABA recommends that you write a control key for all

Peaks systems, so that if small format interchangeable core/large format interchangeable core is added later,

the control key will be properly designed.

Visual Key Control (VKC)

Visual key control is the marking of the face of cores and cylinders with the symbols of the standard key cod-

ing system. From a security standpoint this is not a wise practice. If a key is found, a glance at the face of

the cylinder would reveal what the key operates.

Do not stamp the plug face. This voids the warranty and may collapse the patent pin chamber.

Concealed Key Control (CKC)

Concealed key control is the marking of key symbols on the side or back of cores or cylinders. Kaba marks

the key symbol on the side of the core with a permanent marker. In this way, when the core is recombinated,

the key symbol can be buffed off and no damage will be done.

The TMK Register

Содержание Peaks Classic





























































































Результаты поиска

Содержание Peaks Classic

Отзывы:

Kaba Peaks Classic, Техническое руководство, Страница: 78 / 92

Результаты поиска

Содержание Peaks Classic

Отзывы: