Kaba Peaks Classic Скачать руководство пользователя страница 83

Страница: 83 / 92

lin

r I

lla

tio

Key demountable handle (KDH): Remove cylinder by turning any operating key, de press ing a retainer in the

shank of the handle, and pulling on the handle.

Most contemporary cylindrical locks have key demountable handles.

Non-key demountable handle (

Non-KDH

): Remove cylinder by disassembling the lockset.

Corbin Russwin and Sargent grade 1 knobs and preassembled locksets are the primary

Non-KDH

hardware.

brand

grade 1

grade 2 grade 2

levers

knobs

preassembled levers

knobs

Arrow

KDH

Corbin

KDH

Non-KDH

KDH

KDH/

Non-KDH

Russwin
Falcon

KDH

LSDA

KDH

Marks

KDH

PDQ

KDH

Sargent KDH

Non-KDH

Non-KDH *

KDH

Schlage KDH

KDH

Yale

KDH

1. Turn any operating key

to the right about 45 degrees.

2. Depress the re tain er through the access hole

in the trim, and pull off the knob.

NOTES:

*Sargent discontinued their

unit lock decades ago.

However, they also made a

lock called the “IntegraLock”

(7600 Line) that used a

small mortise body with

through-bolted key-in-knob

trim.

Cylinder Removal Methods

Arrow Architectural Hardware

Division of Assa Abloy

•

“ARROW”

appears on the latch face.

• Basic hand tools required.

NOTES:

• Flexcore is available in small format interchangeable core only.

• Entire Arrow line is available prepped for small format interchangeable core.

Arrow

H series

J series

L, M series

M series

tubular

grade 1

grade 2

deadlocks

knobs & levers interconnected levers

knobs

retrofit type

KDH

Peaks Preferred

8400-xx-1099 8400-xx-1099 8400-xx-1099 8400-xx-1099 8400-xx-1099

Peaks Classic 3400-xx-1099 3400-xx-1099 3400-xx-1099 3400-xx-1099 3400-xx-1099

Section 5 - 3

Содержание Peaks Classic





























































































Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды

Kaba Peaks Classic, Техническое руководство

Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды