Kaba Peaks Classic Скачать руководство пользователя страница 36

Страница: 36 / 92

Section 2 - 24

• 8800/8900 or 3800/6800 small format interchangeable cores can be installed in most cabinet

locks, mailbox locks and switch locks prepped for small format interchangeable core.

• Olympus cabinet lock with Corbin Russwin large format interchangeable cores prep:

use 8144 or 6140 series large format interchangeable cores

• Olympus 720, 721, 722 & 728 series: use 8800/8900 or 3800/6800 series small format

interchangeable cores

• Olympus 700 & 800 series cabinet locks: use 8400-xx-1099 or 3400-xx-1099 with

Olympus 78-Kaba-Conv Kit

• Schlage CL1000 and CL2000 series: use 8400-xx-1099 or 3400-xx-1099 with Schlage

tailpiece and driver

Cabinet Locks and Specialty Applications

8800 or 8900 series and 3800 or 6800 cores fit any padlock

prepared for 6-pin ICore, including:

Abus 381C/45

Falcon

American 3200 & 3500 series

Master Proseries 6400 & 6500

Arrow

Wilson Bohannon

Best (Except .150" Spacing)

For 6-pin core in 7-pin housing, use spacer 3800-00-3007

Medeco 50 series

brass padlocks:

use 6340

Yale 424 and 434

series padlocks:

use 8244 or 6240

Corbin Russwin

PL5070 padlocks:

use 8144 or 6140

Sargent 758 series

padlocks: use

8544 or 6540

Schlage PL4XXX

series padlocks:

use 8444 or 6440

Padlocks—Small Format Interchangeable Core

6-pin 140

Padlocks—Large Format Interchangeable Core

6-pin 140

Содержание Peaks Classic





























































































Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды

Kaba Peaks Classic, Техническое руководство

Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды