Kaba Peaks Classic Скачать руководство пользователя страница 64

Страница: 64 / 92

Section 3 - 20

Comparing A4 Pin Stacks

The examples on this page show pinning for key

symbol 1AA.

When pinning conventional cylinders, ignore the

control bitting. If a top pin of 12 or greater is need-

ed, use two pins of equal length to bring the pin

stack to the required height. When an odd num-

bered top pin is required, such as 15, use two pins

that are close in size–8 and 7 instead of 11 and 4.

For the patent pin chamber in all conventional

cylinders, insert the proper bottom and top patent

pins, then insert a number 4F top pin.

Pinning for all Peaks products can now be accom-

plished with only one spring. That stainless steel

spring is number 3800-00-4010.

Note:

Peaks Preferred Patent Pins for illustration

only. (See key pinning section 3 - 4 to 3 - 12)

top 6 7 10 7 10 6

buildup 6 7 - 7 - 6

master 1 1 1 - 5 -

bottom 2 0 4 1 0 3

top 6 7 10 7 10 6

buildup 6 7 - 7 - 6

master 1 1 1 - 5 -

bottom 2 0 4 1 0 3

top 8 4 6 9 5 7

control 4 10 4 5 5 5

master 1 1 1 - 5 -

bottom 2 0 4 1 0 3

top 8 4 6 9 5 7

control 4 10 4 5 5 5

master 1 1 1 - 5 -

bottom 2 0 4 1 0 3

8400-xx-1206
3400-xx-1206

Key-in-Knob

8400-xx-1299
3400-xx-1299

“99” and “95” Key-in-Knob

8144-xx-1206
6140-xx-1206

Corbin Russwin

8244-xx-1206 Yale
6240-xx-1206 Yale
6340-xx-1206 Medeco

Stack height 15

Stack height 18

Stack height 14

top 7 3 5 8 4 6

control 4 10 4 5 5 5

master 1 1 1 - 5 -

bottom 2 0 4 1 0 3

8800/8900
3800/6800

Small Format

Interchangeable Core

control CTR 153042
master

AA 204153

change 1AA 315103

A4 Keying is not available for the 8444 series cylinders

top 7 8 6 8 6 7

buildup 8 9 7 9 7 8

master 1 1 1 - 5 -

bottom 2 0 4 1 0 3

8401-xx-1210
3401-xx-1210

Rim/Mortise

Calculating Other A4 Pinning Stacks

Содержание Peaks Classic





























































































Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды

Kaba Peaks Classic, Техническое руководство

Результаты поиска

Содержание Peaks Classic

Отзывы:

Похожие инструкции для Peaks Classic

Бренды по названию

Популярные бренды