Stanley Omnilock 45HOM Скачать руководство пользователя

Страница: 1 / 12

Stanley Omnilock

a Product Group of Stanley Security Solutions, Inc.

Planning the installation

T83312/Rev A 000000 ER-7991-12 Jan 2010

Contents

These installation instructions describe how to install
your 45HOM Mortise Lock. Topics covered include:

Planning the installation...

........................................1

Preparing the door and door jamb

..........................4

Installing the lock

........................................................7

Completing the installation

......................................9

Site survey

Use the following survey to record information
about the installation site. You need this information
to determine how to prepare the door for the lock.

Door information

Door handing and bevel:

If a handing change is required, see “Rotate latchbolt
(if necessary)” on page 4.

❐

Left hand (LH)

❐

Left hand, reverse bevel (LHRB)

❐

Right hand (RH)

❐

Right hand, reverse bevel (RHRB)

Door thickness: 1-3/4 to 2 inches (44 to 50 mm).

Environment information

a. See Stanley installation instruction

Addendum (T83317)

Extreme Weatherized Installation

for the extreme weatherized

model installation.

Model

Side of

door

Temperature

Range

Exposure

Standard

Outside

+32°F to +129°F

0°C to +54°C

Drip proof.

Inadvertent

splashing of

water spray

acceptable.

Weatherized

Outside

-4°F to +129°F

-20°C to +54°C

Direct exposure

to rain and snow

Extreme

Weatherized

Outside

-40°F to +129°F
-40°C to + 54°C

Direct exposure

to rain and snow

Inside

+32°F to +129°F

0°C to +54°C

N/A

Installation Instructions for
Stanley Omnilock 45HOM
Mortise Locks

Components checklist

Use the following checklist to make sure that you
have the items necessary to install your Omnilock
Mortise Lock.

Components provided in the box:

❐

Inside and outside trim cassettes

❐

Inside and outside rose and rose ring

❐

Outside escutcheon assembly

❐

Mortise case assembly

❐

Mortise cylinder and collar

❐

Outside lever and spindle assembly

❐

Inside lever

❐

Strike package

❐

Installation template and instructions

❐

Screw package

❐

Mortise case faceplate

❐

Batteries

❐

Torx T15 driver

❐

1/8” hex wrench

Other components:

❐

Programming Default ID Card (provided with

software)

Содержание Omnilock 45HOM













Результаты поиска

Содержание Omnilock 45HOM

Отзывы:

Похожие инструкции для Omnilock 45HOM

Бренды по названию

Популярные бренды

Stanley Omnilock 45HOM, Руководство по установке

Результаты поиска

Содержание Omnilock 45HOM

Отзывы:

Похожие инструкции для Omnilock 45HOM

Бренды по названию

Популярные бренды