Stanley Omnilock 45HOM Скачать руководство пользователя страница 11

Страница: 11 / 12

Installation Instructions for Stanley Omnilock 45HOM Mortise Locks

Stanley Omnilock

a Product Group of Stanley Security Solutions, Inc.

Installation Instructions for Stanley Omnilock 45HOM Mortise Locks

Finishing the installation

Check operation

Check the operation of the lock. For example, check
that:

❐

door latches and opens properly

❐

deadbolt operates properly

❐

key access works

❐

door gap is 1/8” (3 mm)

❐

auxiliary bolt is held inside the case when the

door

is closed.

For assistance, contact your local Stanley Omnilock
dealer.

Test lock

To test the lock for proper operation before the lock
is programmed, follow these instructions:

For keypad locks

1 Press

1234 for the 2000 series, or 5011234

for the 500 series.

The green light flashes and the latch unlock.

2 Turn the lever and open the door.

During the unlock time, the green light flashes. Then
the red light flashes and the latch relocks.

For magnetic stripe or proximity card locks only

Note:

If the lock has a proximity card reader, it may

have already been activated by the presence of an
object near the card reader.

1 Align the magnetic stripe card with the V mark by

the card slot.

2 Insert and then remove the card.

The green light flashes and the latch unlocks.

3 Turn the lever and open the door.

During the unlock time, if using the Programming
Default ID Card, the green light flashes. Then the red
light flashes and the latch relocks.

Содержание Omnilock 45HOM













Результаты поиска

Содержание Omnilock 45HOM

Отзывы:

Бренды по названию

Популярные бренды

Stanley Omnilock 45HOM, Руководство по установке

Результаты поиска

Содержание Omnilock 45HOM

Отзывы:

Бренды по названию

Популярные бренды