Kaba ILCO FDU Скачать руководство пользователя страница 84

Страница: 84 / 276

Front Desk Units - Using and Programming

Kaba Ilco Lodging Access Control System

Australia). Allows the guest and section keycards to override the thumbturn privacy
for given doors.

Shortcut:

Swipe a GMA keycard, press 7, 2, and 4

Default: Disabled

Options: YES:

Enabled

NO: Disabled

Select the “Change Priv Ovr” option, and use the left <

> or right <

> arrow to

toggle between YES and NO. NO will preserve any setting on the locks and YES will
allow modifications.

Select the “Global Priv Ovr” option, and use the left <

> or right <

> arrow to

toggle between YES and NO. NO will disable the privacy override and YES will
enable it.

Notes:

The Global Privacy Override allows the Australian Privacy functionality. This allows
Section and Guest to override the deadbolt.

For use only with 710-II locks with firmware version 1.25 or higher, and 760 locks &
770 locks with firmware version 1.35 or higher.

Содержание ILCO FDU





















































































































































































































































































Результаты поиска

Содержание ILCO FDU

Отзывы:

Kaba ILCO FDU, Руководство пользователя, Страница: 84 / 276

Результаты поиска

Содержание ILCO FDU

Отзывы: