Kaba ILCO FDU Скачать руководство пользователя страница 102

Страница: 102 / 276

Keycards

Kaba Ilco Lodging Access Control System

Press the right <

> arrow to access the available Staff Areas that can be

encoded on the keycard. The available Staff Areas will be listed, defaulting
to NO.

Use the up <

> or down <

> arrows to select each Staff Area and

press the left <

> or right <

> arrow to set the value to YES if it is to

be encoded on the staff keycard. When the areas are set accordingly, press

< >. The following is displayed when ready to encode specific Staff Areas
to a Staff card:

If all 16 Staff Areas are available and set to YES for a Staff keycard the
following is shown:

When all required parameters are set, press < > to encode the keycard
with access to the selected Staff Common Area(s).

4.6.2.2 Guest Common Areas encoding for staff keycard

Applicable Keycards:

Section, Floor, Group, Zone, Area, and Bellman’s Master

Содержание ILCO FDU





















































































































































































































































































Результаты поиска

Содержание ILCO FDU

Отзывы:

Kaba ILCO FDU, Руководство пользователя, Страница: 102 / 276

Результаты поиска

Содержание ILCO FDU

Отзывы: