JVC TH-A9 Скачать руководство пользователя страница 9

Страница: 9 / 41

TH-A9

1-9

Prior to performing the following procedure, remove the
left and right side covers.
Also remove the DVD door.

(Note)

The mechanism slide switch for pickup protection
should be set to the SHORTED position.

Remove the three screws (C) that retain the front
panel assembly, from the bottom panel of the unit.

Remove four screws (D) that retain the DVD mechanism
base, from the top of the unit.

Remove the three screws (E) from the rear panel of
the unit that retain the DVD mechanism base.

Remove the DVD mechanism together with the front
panel assembly by lifting them upward from the
main unit and moving them toward the front.

Disconnect the card wire of the DVD mechanism
from the connector CN101 on the DVD servo board.

Disconnect the wire of the LED board from the
connector CN812 on the analog input/output board.

Removing the front panel assembly and
the DVD mechanism base

(See Figs.3 to 7)

Remove the front panel assembly and the
DVD mechanism together, just as they were
assembled.

Bottom panel

Front panel assembly

DVD mechanism base

Front panel assembly

DVD mechanism base

Rear panel

DVD mechanism base

Analog I/O board

CN812

Front panel assembly

DVD servo board

CN101

DVD servo board

CN101

DVD mechanism assembly

LED board

Analog I/O board

CN812

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

Содержание TH-A9










































Результаты поиска

Содержание TH-A9

Отзывы:

Похожие инструкции для TH-A9

Бренды по названию

Популярные бренды

JVC TH-A9, Руководство по обслуживанию

Результаты поиска

Содержание TH-A9

Отзывы:

Похожие инструкции для TH-A9

Бренды по названию

Популярные бренды