JVC TH-A9 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 41

background image

TH-A9

1-14

Prior to performing the following procedure, remove
the left and right side covers.
Also remove the DVD door.
Also remove the front panel assembly and the DVD
mechanism base.
Also remove the analog board.
Also remove the gear motor assembly.
Also remove the door arm assembly.

Remove the two screws (U) that retain the door arm
board (L).

Remove two screws (U) that retain the door arm
board (R).

Removing the door arm boards (L) and (R)

(See Figs.24 and 25)

1.

2.

Prior to performing the following procedure, remove
the left and right side covers.
Also remove the DVD door.
Also remove the front panel assembly and the DVD
mechanism base.
Also remove the analog board.
Also remove the gear motor assembly.
Also remove the door arm assembly.

Remove the screw (V) that retains the power supply
board, from the top of the unit.

Remove three screws (W) that retain the power
supply board, from the rear panel of the unit.

Pull out the power supply board from clamp a.

Disconnect the wire from the connector CN972 on
the power supply board, and then remove the power
supply board in the direction of the arrow while
unplugging the connectors CN951 and CN952 from
the analog input/output board.

Removing the power supply board

(See Figs.26 and 27)

1.

2.

3.

4.

U

Door arm board (L)

U

U

U

Door arm board (R)

Analog I/O board

Power supply board

Power supply board

CN972

V

CN952

CN951

Power supply board

CN952

CN951

W

W

Rear panel

Fig.24

Fig.25

Fig.26

Fig.27

Clamp a

Clamp a

«
...
12
13
14
15
16
...
»

Содержание TH-A9










































Отзывы:

Нет отзывов

Похожие инструкции для TH-A9

ZEB Juke Bar 1500

Бренд: Zebronics Страницы: 5

Бренд: S.E.M. Страницы: 6

Бренд: Dynacord Страницы: 2

Бренд: Novetec Страницы: 7

Бренд: Cambridge SoundWorks Страницы: 11

Бренд: Fireside Audiobox Страницы: 12

Бренд: Bang & Olufsen Страницы: 44

Бренд: JBL Страницы: 4

Бренд: Radar Systems Страницы: 65

Бренд: Sullair Страницы: 56

Бренд: Viessmann Страницы: 100

Бренд: Hitachi Страницы: 14

Бренд: Hitachi Страницы: 4

Бренд: Hitachi Страницы: 4

Бренд: Hitachi Страницы: 28

Бренд: Hitachi Страницы: 32

Бренд: Hitachi Страницы: 40

Бренд: Hitachi Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды