JVC TH-A9 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 41

background image

TH-A9

1-19

Prior to performing the following procedure, remove the
heat sink cover, the amplifier assembly, the amplifier
cover, the preamplifier board, the power supply & SP
terminal board, the main amplifier board and power
amplifier board (A).

Remove the four screws L attaching the power
amplifier board (B) to the heat sink.

Release the four joint hooks c bent and attached to
the outside of the power amplifier board (B).

Move the power amplifier board (B) in the direction of
the arrow to release joint d and remove the power
amplifier board (B) from the bracket (B).

Removing the power amplifier board (B)

(See Figs.9 and 11)

1.

2.

3.

Prior to performing the following procedure, remove
the heat sink cover, the amplifier assembly, the
amplifier cover, the preamplifier board, the power
supply & SP terminal board, the main amplifier
board, the power amplifier board (A) and power
amplifier board (B).

Disconnect the harness from connector CN104 on
the main amplifier board.

Disconnect the wire from connector CN107 on the
power supply & SP terminal board.

Remove the four screws M attaching the power
transformer.

Removing the power transformer

(See Figs.12 and 13)

1.

2.

3.

Prior to performing the following procedure, remove
the heat sink cover, the amplifier assembly, the
amplifier cover, the preamplifier board, the power
supply & SP terminal board, the main amplidier
board, the power amplifier board (A), the power
amplifier board (B) and power transformer.

Disconnect the wire from connector CN108 on the
power supply & SP terminal board.

Remove the two screws N attaching the AC power
cord.

Removing the AC power cord

(See Fig.12)

1.

2.

CN101

Fig.11

Fig.12

Fig.13

Hooks

Main amplifier

board

Power supply

& SP terminal

board

Power supply

& SP terminal

board

CN104

Power

transformer

Joint c

Joint c

CN106

CN105

Power amplifier

board (B)

M

M

M

Joint d

CN108

N

N

AC cord

Cord stopper

braket

Preamplifier

board

Main amplifier

board

Braket (B)

CN107

CN111

CN110

CN108

CN107

«
...
17
18
19
20
21
...
»

Содержание TH-A9










































Отзывы:

Нет отзывов

Похожие инструкции для TH-A9

Бренд: L-Acoustics Страницы: 38

Бренд: L-Acoustics Страницы: 31

Бренд: L-Acoustics Страницы: 24

Бренд: L-Acoustics Страницы: 201

Бренд: Yamaha Страницы: 83

Бренд: Yamaha Страницы: 7

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 14

Бренд: Yamaha Страницы: 10

Бренд: Yamaha Страницы: 50

Бренд: Yamaha Страницы: 8

Бренд: Concertone Страницы: 12

Бренд: Cyrus Страницы: 6

ORDERCODE D3710

Бренд: DAPAudio Страницы: 13

Бренд: Onkyo Страницы: 9

Sportsound SSR-300

Бренд: Daktronics Страницы: 6

Бренд: Infinity Страницы: 10

Бренд: K.M.E. Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды