JVC TH-A9 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 41

background image

TH-A9

1-18

Prior to performing the following procedure, remove the
heat sink cover, amplifier assembly, the amplifier cover,
the preamplifier board, the power supply & SP terminal
board, the main amplifier board.

Remove the four screws K attaching the power
amplifier board (A) to the heat sink.

Release the four joint hooks a bent and attached to
the outside of the power amplifier board (A).

Move the power amplifier board (A) in the direction of
the arrow to release joint b and remove the power
amplifier board (A) from the bracket (A).

1.

2.

3.

Removing the power amplifier board (A)

(See Figs.9 and 10)

Prior to performing the following procedure, remove the
heat sink cover, the amplifier board, the amplifier
cover, the preamplifier board and the power supply &
SP terminal board.

Disconnect the harness from connector CN104 on
the main amplifier board.

Remove the seven screws H and the main amplifier
board with the heat sink.

Remove the two screws I attaching the power
amplifier board (A) and the two screws J attaching
the power amplifier board (B) on the underside of the
main amplifier board.

Disconnect connector CN102 and CN103 on the
power amplifier board (A) and CN105 and CN106 on
the power amplifier board (B) from the main amplifier
board respectively.

1.

2.

3.

4.

Removing the Main amplifier Board

(See Figs.7 and 8)

H

Fig.7

Fig.8

Fig.9

Fig.10

H

I

J

I

J

L

K

L

L

K

K

K

CN104

CN102

CN103

CN106

CN105

Power amplifier

board (A)

Power amplifier

board (A)

Power amplifier

board (A)

Braket(A)

Joint a

Hooks

Joint a

Joint b

CN102

CN103

Braket (B)

Heat sink

CN103

CN102

CN106

CN105

Power amplifier

board (B)

Power amplifier

board (B)

Power

transformer

Main amplifier

board

Braket (A)

Main amplifier

board

H

H

«
...
16
17
18
19
20
...
»

Содержание TH-A9










































Отзывы:

Нет отзывов

Похожие инструкции для TH-A9

FUSION Apollo MS-WB670

Бренд: Garmin Страницы: 44

ZEB Juke Bar 1500

Бренд: Zebronics Страницы: 5

Soundmaster 138

Бренд: SOUNDMASTER Страницы: 1

Бренд: S.E.M. Страницы: 6

Бренд: Magnavox Страницы: 33

Total Solutions TSS-800

Бренд: Infinity Страницы: 26

Бренд: Klipsch Страницы: 30

CLI U12 SD0F1110 NG B/U

Бренд: Velux Страницы: 56

Бренд: Skytec Страницы: 30

Бренд: Aqua-Hot Страницы: 49

Бренд: SAL Страницы: 20

POWER DUO ABT385

Бренд: Altec Lansing Страницы: 12

Бренд: WaterGroup Страницы: 24

Бренд: Soundstage Страницы: 13

Бренд: Hybrid Audio Technologies Страницы: 23

Бренд: EAW Страницы: 2

Бренд: RCA Страницы: 68

Бренд: A&S Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды