JVC TH-A9 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 41

background image

TH-A9

1-12

Prior to performing the following procedure, remove the
left and right side covers.
Also remove the DVD door.
Also remove the front panel assembly and the DVD
mechanism base.
Also remove the analog board.

Disconnect the wire from the connector CN106 on
the analog input/output board.

Remove the two screws (P) that retain the gear
motor assembly and remove the assembly in the
direction of the arrow.

Remove the belt from the gear motor assembly.

Remove two screws Q that retain the gear motor.

(Note)

Prior to performing the following procedure, remove the
left and right side covers.
Also remove the DVD door.
Also remove the front panel assembly and the DVD
mechanism base.

Disconnect the wire from the connector CN972 on
the power supply board.

Remove the two screws N that retain the fan motor
assembly, from the right side of the unit.

Remove the two screws (O) that attach the fan motor
assembly to the fan bracket.

Removing the fan motor assembly

(See Figs.15 and 16)

1.

2.

3.

When reassembling, check that the gear motor
assembly is engaged properly with the door arm
assembly at the engaging points (c) and (d).

Removing the gear motor assembly

(See Figs.17 to 19)

1.

2.

3.

4.

N

Fig.15

Fig.16

Fig.17

Fig.18

Fig.19

N

Fan motor assembly

Power supply board

CN972

O

O

Fan motor

Fan bracket

Gear motor assembly

Analog I/O board

CN106

P

Analog I/O board

CN106

Gear motor assembly

P

P

Engaging

point (c)

Engaging

point (d)

Gear motor

Belt

Q

«
...
10
11
12
13
14
...
»

Содержание TH-A9










































Отзывы:

Нет отзывов

Похожие инструкции для TH-A9

Бренд: Yamaha Страницы: 24

JBL BAR 5.0 MULTIBEAM

Бренд: Harman Страницы: 25

Бренд: JBL Страницы: 24

Бренд: Jensen Страницы: 2

LA SPHERE - DATASHEET 2

Бренд: CABASSE Страницы: 8

Бренд: Furrion Страницы: 21

Бренд: EAW Страницы: 2

Бренд: Pyle Страницы: 6

Бренд: Teac Страницы: 38

Бренд: Cambridge SoundWorks Страницы: 11

Бренд: TCL Страницы: 20

Бренд: ubbink Страницы: 61

Бренд: Denon Страницы: 16

2-way Full Loudspeaker System UB42

Бренд: EAW Страницы: 2

Disco Jam PSUFM1035A

Бренд: Pyle Страницы: 5

Бренд: Montarbo Страницы: 36

Бренд: Electro-Voice Страницы: 2

Бренд: Commodore Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды