Jung DS 4092 TS Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 143

background image

Art. No. DS 4092 TS

up

A short time telegram (UP) is triggered
by a short signal length and a long time
telegram (high) is triggered by a long
signal length.

Down

A short time telegram (DOWN) is
triggered by a short signal length and a
long time telegram (low) is triggered by
a long signal length.

Toggle

With this setting, the direction is
switched over internally long signal
length (MOVE). If a short time signal
transmits a STEP telegram, then this
STEP is always switched in the opposite
direction of the last MOVE. Several
STEP telegrams transmitted
successively are switched in the same
direction.

Behaviour after bus
voltage
return

After a device reset (bus voltage return
or ETS programming operation), the
communication object "Long time
operation" of the input can be initialised.
If, in the ETS, a delay is set for the
extension inputs after bus voltage
return, the device only transmits the
telegrams when the delay has elapsed.

No reaction

After a device reset, no reaction takes
place automatically (no telegram is
transmitted to the bus).

up

In this configuration, an "UP" telegram is
actively transmitted to the bus after a
device reset.

Down

In this configuration, an "DOWN"
telegram is actively transmitted to the
bus after a device reset.

Operation concept

This parameter specifies the telegram
sequence after actuation (rising edge).

short – long - short

A STEP is transmitted with a rising edge
and the "Time between short and long
time operation" started. This step serves
to stop a continuous run in progress. If,
within the started time, a falling edge is
detected, the input does not transmit an
additional telegram. If no falling edge
was detected during the time, a MOVE
is transmitted automatically after the
time has elapsed and the "slat
adjustment time" is started. If a falling
edge is detected within the slat
adjustment time, the input transmits a
STEP. This function is used for slat
adjustment.

long - short

A MOVE is transmitted when there is a
rising edge at the input and the "slat

Page 130 of 143

Software "Rotary sensor with extensions 10FE1x"

Parameters

«
...
128
129
130
131
132
...
»

Содержание DS 4092 TS
















































































































































Отзывы:

Нет отзывов

Похожие инструкции для DS 4092 TS

Бренд: 4B Страницы: 12

Бренд: IFM Electronic Страницы: 16

Бренд: IFM Electronic Страницы: 6

Бренд: Manfrotto Страницы: 2

Бренд: Manfrotto Страницы: 2

Бренд: Mammut Страницы: 32

Бренд: VDO Cyclecomputing Страницы: 21

Бренд: Panasonic Страницы: 120

Merrytec MK054V RC Series

Бренд: V-TAC Страницы: 105

Бренд: AccuAir Страницы: 40

Бренд: Peak Страницы: 10

Бренд: Z-Wave Страницы: 10

Бренд: Roav Страницы: 10

Бренд: SUP’AIR Страницы: 29

MEDIA WIRELESS DESKTOP 800 -

Бренд: LABTEC Страницы: 12

Бренд: handi quilter Страницы: 2

ALK.00.733.15000/B

Бренд: SW-Motech Страницы: 14

Бренд: Bioenno Power Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды