Jung DS 4092 TS Скачать руководство пользователя страница 124 | Manualshive

Страница: 124 / 143

background image

Art. No. DS 4092 TS

"level 4 (loud)". The level "mute (OFF)"
deactivates the buzzer at the selected
volume.
This parameter defines the volume 1.

Volume 2

mute (OFF)

Level 1 (quiet)
Level 2
Level 3
Level 4 (loud)

The buzzer can output signal tones at
different volumes. The volume for the
function-dependent signals and
warning/ring tone can be differentiated
into two settings (volume 1, volume 2)
and switched over by a 1-bit
communication object during regular
operation of the device. In this way, for
instance, adaptation to local conditions
or a change-over from day to night (
loud <-> quiet) is possible. The volume
can be set at up 5 different levels. A
setting between "level 1 (quiet)" and
"level 4 (loud)". The level "mute (OFF)"
deactivates the buzzer at the selected
volume.
This parameter defines the volume 2.

Alarm volume

mute (OFF)
Level 1 (quiet)
Level 2
Level 3

Level 4 (loud)

This parameter specifies the volume of
the alarm tone.
This parameter is only visible if the
alarm function is enabled!

Object polarity for
volume
switch-over

"0" = Volume 1 /
"1" = Volume 2

"0" = Volume 2 /
"1" = Volume 1

This parameter defines the telegram
polarity of the object for switching over
volume.

Alarm function

disabled

enabled

The device permits signalling of a alarm
which might be, for instance, a burglar
or a fire alarm from a KNX central alarm
unit. If the alarm message has been
activated, the buzzer outputs a pulsating
tone at a frequency of approx. 2 Hz at a
volume configurable separately for the
alarm message. In addition, the red
diagnostic LEDs flash at the same
frequency.
The signalling of an alarm can be
enabled separately by this parameter.

Object polarity "alarm
message"

"1" = Alarm /
"0" = Resetting alarm

"0" = Alarm /
"1" = Resetting alarm

This parameter defines the telegram
polarity of the "Switch alarm". When the
object value corresponds to the "Alarm"
state, the buzzer outputs the alarm tone.
The alarm function then overrides
acoustic signalling with lower priority.

Page 124 of 143

Software "Rotary sensor with extensions 10FE1x"

Parameters

«
...
122
123
124
125
126
...
»

Содержание DS 4092 TS
















































































































































Отзывы:

Нет отзывов

Похожие инструкции для DS 4092 TS

Бренд: Makita Страницы: 20

Бренд: Metra Electronics Страницы: 14

Speedglas G5-02

Бренд: 3M Страницы: 17

Speedglas 9100 MP

Бренд: 3M Страницы: 72

Speedglas 9100-Air

Бренд: 3M Страницы: 63

Бренд: 3M Страницы: 84

Бренд: Farenheit Страницы: 8

Бренд: Napoleon Страницы: 4

Бренд: V-TAC Страницы: 4

SANTA FCB-XM-CH0084-120V

Бренд: GE Страницы: 2

Бренд: Warmon Страницы: 2

IQ MINI DW S Series

Бренд: QOLSYS Страницы: 2

Бренд: Bebob Страницы: 4

Бренд: WABCO Страницы: 48

Бренд: iBeam Страницы: 2

Бренд: Smith-Victor Страницы: 2

Бренд: Datasensor Страницы: 3

Бренд: BrandMotion Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды