Jandy HI-E2, Инструкция по установке и эксплуатации

Страница: 4 / 40

Page 4
ENGLISH
Jandy
®
Pro Series, Hi-E2
®
and Hi-E2R Gas-Fired Heater
|
Installation & Operation Manual
Section 1. General Information
1.1 Introduction
This manual contains information for the proper
installation and operation of the Hi-E
2
and Hi-E
2
R Model
EHE pool/spa heater. Certain sections are specific to
United States or Canadian installations, and are labeled
United States or Canada. Procedures in this manual must
be followed exactly. To obtain a copy of this manual
contact Zodiac Pool Systems, Inc. ("Zodiac
®
"). For
address information. See back cover.
1.2 Description
The Hi-E
2
Low NOx heater is a very efficient gas-fired
pool and spa heater. Its combustion system includes a
heat exchanger which extracts 95% of the energy in the
gas fuel. It has no standing pilot burner. It exceeds the
requirements of energy conservation regulations such as
those in California, Hawaii, New York, Oregon and other
states which require that a pool heater have intermittent
ignition.
The heater is designed to operate in conventional
swimming pool and spa equipment arrangements. It
requires 115V 60 Hz electrical power. It has the versatile
dual-thermostat control system for pool/spa combinations.
The Hi-E
2
is certified by CSA International to comply with
latest editions of applicable standards. In the United States,
the applicable standard is ANSI Standard Z21.56 for gas-
fired pool heaters. In Canada, it is Standard CSA 4.7.
The Hi-E
2
Low NOx heater has been designed specifically
to heat fresh water swimming pools and spas, and with
proper installation and care, it will provide years of
reliable service. Do not use it to maintain pool or spa
water temperature below 70°F. Do not use it as a heating
boiler or general service water heater or to heat true salt
water systems where salinity is in the 35,000 ppm range.
For special applications, consult your Jandy Pro Series
dealer.
1.3 Warranty
The Hi-E
2
is sold with a limited factory warranty. A copy
of the warranty is included in a plastic bag inside the
heater. The warranty does not cover damage caused by
improper installation, operation, or field modification; or
damage to the heat exchanger caused by corrosive water.
See Section 3.4 for guidelines on pool water chemistry.
WARNING
Improper installation or maintenance can cause nausea
or asphyxiation from carbon monoxide in flue gases
which could result in severe injury, or death. For indoor
installations, as an additional measure of safety, Zodiac
Pool Systems, Inc. strongly recommends installation of
suitable Carbon Monoxide detectors in the vicinity of this
appliance and in any adjacent occupied spaces.
Section 2. Installation Instructions
2.1 General Requirements
All gas-fired products require correct installation to assure
safe and satisfactory operation. The requirements for pool
heaters include the following:
1. Appropriate site location and clearances.
2. Sufficient supply of clean air for combustion and
ventilation.
3. Proper venting of products of combustion.
4. Properly sized gas pipe.
5. Properly sized gas meter.
6. Adequate water flow.
7. Provision for disposal of combustion condensate
water.
In the United States, installation must be in accordance
with local codes and the most recent edition of the
National Fuel Gas Code, ANSI Z223.1/NFPA-54. The
Code can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169
www.nfpa.org
In Canada, install the heater in accordance with local
codes and the most recent edition of the Natural Gas and
Propane Installation Code, CAN/CSA B149.1.
Special Precautions
Liquefied petroleum (LP) gas is heavier than air.
Therefore, a pool heater using LP gas is subject to special
installation rules. Consult local codes and fire protection
authorities about specific installation restrictions.
Fuel gas and its combustion products are known to cause
cancer or harm the reproductive process. Follow these
installation instructions and applicable codes exactly to
avoid this.