ITT Goulds Pumps ICB Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 72

background image

NOTICE:

Use only lubricants when you are sure that there can´t occur any dangerous reactions between
the pumpage and the lubricant.

NOTICE:

Make all required parts available, so that assembly can be completed quickly. The lubricants
are only effective for a short time. After that the axial movability and, thus, the automatic adjust-
ment of the elastomeres is lost.

NOTICE:

Don´t push elastomers over sharp edges. If necessary use mounting devices.

•

Put throttle bush (542.31) into quench cover (471Q) carefully.

•

Press the stationary part of the mechanical seal in the quench cover (471Q). For this you can even-
tually use a stamp with a soft surface. Unequal load can lead to cracking of the seal face.

•

Don´t damage seal face!

•

Pay attention that the stationary ring is in solid contact with the quench cover. The seal face must
be installed perpendicular to the shaft.

•

If a pin (560) is existing, be careful that it fits into the slot of the mechanical sealing, without touch-
ing the mechanical seal.

•

Insert casing cover (161) carefully, until it fits axially in the bearing frame lantern (344).

•

Push the rotating unit of the mechanical seal on the shaft (210).

•

Adjust the face on the impeller side of the mechanical seal exactly on measure A. For mechanical
seals without own set screws the fixing ring (527) serves as a stop.

NOTICE:

Push mechanical seals with bellows in such a way, that the bellow is compressed and not
stretched (danger of tearing apart!).

NOTICE:

Use anti-friction device (Molykote, etc.) between shaft sleeve and shaft only, if you are sure
that no dangerous reactions between pumped liquid and anti-friction device can occur.

•

Further assembly and installation of pump acc. Dismantling and repair of pump of Installation, Op-
eration and Maintenance Instruction.

NOTICE:

Before starting the pump connect flushing system for quench and put it into operation.

10.3 Design: S1...2 Single mech. seal, unbalanced (DIN 24960,
l

1k

/ EN 12756, design K, form U), Impeller with back vanes

You find the shaft sealing of your pump on the data sheet / the order confirmation. Refer to

Design cod-

ing system

, as well.

10.3 Design: S1...2 Single mech. seal, unbalanced (DIN 24960, l1k / EN 12756, design K, form U), Impeller with back vanes

54

ICB Installation, Operation and Maintenance Instruction

«
...
54
55
56
57
58
...
»

Содержание Goulds Pumps ICB









































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps ICB

Бренд: Eagle Страницы: 16

Бренд: Calpeda Страницы: 44

Бренд: Calpeda Страницы: 64

Бренд: Calpeda Страницы: 32

Бренд: Lavor Страницы: 108

Craftsman 390.269451

Бренд: Sears Страницы: 8

Бренд: P.Lindberg Страницы: 54

Бренд: SMC Networks Страницы: 19

Бренд: EMI Страницы: 5

Бренд: PAPILLON Страницы: 16

Бренд: GE Страницы: 28

BC-F20HWR2-200L

Бренд: enertik Страницы: 33

Бренд: Edwards Страницы: 60

Бренд: EBARA Страницы: 28

Blue Diamond MaxiBlue

Бренд: Charles Austen Страницы: 20

Бренд: salmson Страницы: 40

Бренд: BLACKMER Страницы: 12

Optyma Plus INVERTER Series

Бренд: Danfoss Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды