ITT Goulds Pumps ICB Скачать руководство пользователя страница 23

Страница: 23 / 72

Guideline

Explanation/comment

Do not install and operate the equipment in closed
systems unless the system is constructed with
properly-sized safety devices and control devices.

Acceptable devices:

•

Pressure relief valves

•

Compression tanks

•

Pressure controls

•

Temperature controls

•

Flow controls

If the system does not include these devices, consult the engi-
neer or architect in charge before you operate the pump.

Take into consideration the occurrence of unwant-
ed noise and vibration.

The best pump location for noise and vibration absorption is on
a concrete floor with subsoil underneath.

If the pump location is overhead, undertake special
precautions to reduce possible noise transmission.

Consider a consultation with a noise specialist.

5.1.2 Foundation requirements

Requirements

•

The location and size of the foundation bolt holes must match those shown on the assembly draw-
ing provided with the pump data package.

•

The foundation must weigh between two and three times the weight of the pump.

•

Provide a flat, substantial concrete foundation in order to prevent strain and distortion when you
tighten the foundation bolts.

•

The concrete foundation must have sufficient firmness according to DIN 1045 or equal standard.

Sleeve-type bolts

Item Description

Baseplate

Shims

Foundation

Sleeve

Dam

Bolt

Figure 4: Sleeve type bolts

5.1 Pre-installation

ICB Installation, Operation and Maintenance Instruction

Содержание Goulds Pumps ICB









































































Результаты поиска

Содержание Goulds Pumps ICB

Отзывы:

Похожие инструкции для Goulds Pumps ICB

Бренды по названию

Популярные бренды

ITT Goulds Pumps ICB, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps ICB

Отзывы:

Похожие инструкции для Goulds Pumps ICB

Бренды по названию

Популярные бренды