ITT Goulds Pumps ICB Скачать руководство пользователя страница 17

Страница: 17 / 72

Figure 2: Pump lifting

3.1.3 Storage guidelines

3.1.3.1 Pump storage requirements

Storage requirements depend on the amount of time that you store the unit. The normal packaging is
designed only to protect the unit during shipping.

Length of time in
storage

Storage requirements

Upon receipt/short-
term (less than six
months)

•

Store in a covered and dry location.

Long-term (more than
six months)

•

Store in a covered and dry location.

•

Store the unit free from heat, dirt, and vibrations.

•

Rotate the shaft by hand several times at least every three months.

•

All suction and discharge branches, and all other intakes and outlets must be closed
with dummy flanges or plugs

•

For longer periods of storage conservation measurements at machines surfaces and
packing with moisture protection may be necessary

3.1.3.2 Frostproofing

Table 3: Situations when the pump is or is not frostproof

Situation

Condition

Operating

The pump is frostproof.

3.1 Transportation and Storage

ICB Installation, Operation and Maintenance Instruction

Содержание Goulds Pumps ICB









































































Результаты поиска

Содержание Goulds Pumps ICB

Отзывы:

Похожие инструкции для Goulds Pumps ICB

Бренды по названию

Популярные бренды

ITT Goulds Pumps ICB, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps ICB

Отзывы:

Похожие инструкции для Goulds Pumps ICB

Бренды по названию

Популярные бренды