ITT Goulds Pumps ICB Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 72

background image

Before disassembly check if required parts are ready.

Disassemble the pump only so far, as required for the replacement of the repair part.

7.1.8 Removal and Installation of screen in the motor lantern

The guard plates (680) are fixed in the windows of the motor lantern (681).

For removing insert a screwdriver about 4 cm into the last row with punches of the guard plate. Then pull
up the screwdriver until the lower edge of the guard plate lifts off the window. Now you can remove the
screwdriver together with the guard plate from the window see

Figure 8: Motor lantern screen removal on

.

On installation insert the screwdriver about 4 cm into the last row with punches of the guard plate. Then
put the upper part of the guard plate into the upper edge of the window. Now pull up the screw driver until
the guard plate is bent through so much, that it can be inserted into the lower edge of the window of the
motor lantern.

Figure 8: Motor lantern screen removal

NOTICE:

Pull up screw driver only so far as is absolutely necessary to insert the guard plate into the win-
dow. If the guard plate does not stick fast in the window after installation:

Dismantle guard plate once again, flatten it and install again.

7.1.9 Removal of the Back Pull Out Assembly

The back pull out assembly consists of all pump parts except the volute casing (102V). As the pumps are
constructed in block design, the volute casing (102V) can remain on the foundation and in the piping, if it
´s not the volute casing itself, which must be repaired.

1.

Drain volute casing (102V) via drain plug (912.11).

2.

Loosen screws of existing sealing or flushing piping.

3.

Loosen screws of support food (183) from the foundation (not existing on all sizes).

4.

Hang the Back Pull Out Assembly onto a lifting device, so that it won´t sink down or press into the
volute casing during the dismounting.

5.

Loosen hex head bolt (901.11) from the casing.

6.

Using the jack screws provided (901.42), separate the Back Pull Out Assembly from the casing.

7.1 Maintenance

ICB Installation, Operation and Maintenance Instruction

35

«
...
35
36
37
38
39
...
»

Содержание Goulds Pumps ICB









































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps ICB

Zoneline AZ85H09DAC

Бренд: GE Страницы: 2

Бренд: GE Страницы: 2

Бренд: AromaMist Страницы: 15

Бренд: Gude Страницы: 62

Бренд: PAPILLON Страницы: 16

HELIFLOW 8 Series

Бренд: Gardner Denver Страницы: 64

FIGHTER 2010 Series

Бренд: Nibe Страницы: 36

Power Vent Raytherm 2100

Бренд: Raypak Страницы: 2

Бренд: SFA Страницы: 80

SHERPA MONOBLOC

Бренд: Olimpia splendid Страницы: 192

Бренд: JABSCO Страницы: 4

Бренд: Alfa Laval Страницы: 34

FlexGas Hi Delta H 302CD-2342CD

Бренд: Raypak Страницы: 13

Бренд: VAKI Страницы: 9

Бренд: Calorex Страницы: 28

Бренд: Malibu Boats Страницы: 2

Optyma OP-SMLZ Series

Бренд: Danfoss Страницы: 4

Бренд: YAMADA Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды