ITT Goulds Pumps ICB Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 72

background image

Radial clear-
ances (mm)

new

min. 0,15 0,17 0,20 0,22 0,25
max. 0,19 0,22 0,24 0,27 0,30

worn

0,78 0,85 0,90 1,05 1,15

Axial

clearance a
(mm)

new

0,8 - 1,2

worn

max. 1,7

When the wear limits has been reached or exceeded, the worn parts must be replaced.

For volute casings (102V) with a wear ring (502.11) and cover casings (161) with a wear ring (502.31)
there are the following possibilities to restore the correct clearance:

1.

Renew impeller (230) and wear ring. Then the original measures are restored.

2.

A customized wear ring (bored to fit) can be supplied to avoid replacement of the impeller. Please
contact factory for details.

When volute casing (102V) or casing cover (161) without wear ring must be repaired, a wear ring can be
installed to renew pump performance. Re-machining of the volute casing and / or casing cover is re-
quired. Please contact the factory for details and assistance.

7.1.14 Reassembly

7.1.14.1 Mounting

1.

Re-assemble the pumps using the reverse order of steps as completed for pump disassembly.
However the following observations should be considered:

•

Pay attention to the utmost cleanliness when re-assembling the pump.

•

For tight tolerances e.g. between stub shaft (210) and motor shaft or impeller (230) and
shaft (210), as well as thread, use suitable anti-galling compound (e.g. Molykote / Never-
Seeze), so that the next mounting and dismounting will be easier.

NOTICE:

Anti-galling compound must be compatible with the pumpage.

Screws should be tightened, with the following torque:

Location

Screw

Size

Screw torque in Nm

Lubricated

threads

Dry threads

Casing screws

M12

35

50

M16

105

150

M20

210

305

All other screws

M10

35

50

M12

60

90

M16

150

220

Do not use excessive force.

2.

For mounting of stub shaft refer to

Mounting of Stub Shaft

.

3.

For mounting of mechanical seal refer to separate "Mounting Instruction of Shaft Sealing" and

7.1.10 Removal of Impeller on page 36

4.

For impellers with back vanes the axial clearance between the back vanes and the casing cover
(161) should be checked after mounting the impeller (230) and tightening the impeller nut (922) (see
Clearance at impellerchapter.

7.1 Maintenance

38

ICB Installation, Operation and Maintenance Instruction

«
...
38
39
40
41
42
...
»

Содержание Goulds Pumps ICB









































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps ICB

Бренд: Nastec Страницы: 28

Бренд: WarmPool Страницы: 26

Бренд: YUKEN KOGYO Страницы: 82

Бренд: Gardner Denver Страницы: 27

Nano-Flow 2,600

Бренд: Cobalt Digital Inc Страницы: 2

Бренд: K&T Страницы: 17

Бренд: Daikin Страницы: 12

Бренд: KAMMAK Страницы: 8

Бренд: Airetool Страницы: 20

Бренд: Graco Страницы: 10

Бренд: EMP Страницы: 18

Wilden Advanced P400

Бренд: Dover Страницы: 56

MAHRW010ZAB-270

Бренд: Siddons Solarstream Страницы: 24

Бренд: DAB Страницы: 37

Бренд: GEA Страницы: 44

Welch Chemstar Dry 2070

Бренд: Gardner Denver Страницы: 16

Бренд: Carrier Страницы: 10

DIGITAL LOGIC AT400

Бренд: Calorex Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды