ITT Goulds Pumps ICB Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 72

background image

161 Casing cover

527 a) Fixing ring

210 Shaft

560 b) Pin

230 Impeller

904.31 a) Set screw

412.21 O-ring

904.32*) Set screw

433 Mech. seal

922 Impeller nut

502.31*) Wear ring

940.31 Key

*) optional

a) not for all designs

b) only for mech. seals with PTFE-O-rings

Nominal size

of mech.

seal

∅

d

1

∅

d

7

l

1K

A

B

∅

d

L

33

33

48

42,5

7,5

50

19

43

43

61

45

7,5

52,5

28

53

53

73

47,5

10

57,5

38

This leaflet is subject to alteration!

10.1.3 Removal of mechanical seal

For that purpose use the appropriate sectional drawing and the enclosed data sheet of the mechanical
seal.

•

Remove and disassemble the pump acc. to the Installation, Operation and Maintenance Instruc-
tions including

7.1.11 Remove the Shaft Sealing on page 36

•

Remove fixing ring (527) (if existing) and rotating part of the mechanical seal (433) from shaft (210).
Refer to the enclosed data sheet of the mechanical seal, if set screws are to be loosened at the
mechanical seal at first.

•

Remove stationary part of the mechanical seal (433) out of the casing cover (161).

Clean drilling for stationary seal rng (

∅

d

7

) in the casing cover (161) and surface of shaft (210).

NOTICE:

The reuse of mechanical seals, which have already been used for a longer time, can lead to
leaking at the seal faces after re-installation. Therefore the replacement of the mechanical seal
through a new one is recommended. The dismounted mechanical seal can be reconditioned by
the manufacturer and serve as a replacement mechanical seal.

10.1.4 Installation of a mechanical seal

For that purpose use the sectional drawing and data sheet of the mechanical seal.

It is only allowed to install mechanical seals, which have a certificate of Conformity acc. the Directive

94/9/EC.

On changing the mechanical seal type resp. the mechanical seal manufacturer the data regarding max.
operating temperature of the pumped medium and temperature class must be checked again.

10.1 Single mech. seal without shaft sleeve (Design code S1..2)

ICB Installation, Operation and Maintenance Instruction

49

«
...
49
50
51
52
53
...
»

Содержание Goulds Pumps ICB









































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps ICB

Бренд: Makita Страницы: 96

Бренд: vacuubrand Страницы: 44

Бренд: Radiant Страницы: 8

Бренд: Chiltrix Страницы: 54

Бренд: Barracuda PUMPS Страницы: 4

Бренд: Wacker Neuson Страницы: 64

Бренд: F.F. Group Страницы: 28

Godiva Prima SmartCAFS PC1 Series

Бренд: Idex Страницы: 68

Бренд: Grundfos Страницы: 20

Бренд: Trotec Страницы: 18

Бренд: RHOSS Страницы: 344

Бренд: Kimray Страницы: 24

Pneumatic grease pump 50:1

Бренд: Pressol Страницы: 14

Peristaltic Pump 2.8 l/h

Бренд: Jesco Страницы: 28

Бренд: Fluke Calibration Страницы: 28

SIMEL GEH 700/0,4 C

Бренд: Tyco Electronics Страницы: 23

Comfort Solutions 1900e Series

Бренд: Taco Страницы: 12

F 550 GS6 Series

Бренд: Flux Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды