ITT Goulds Pumps ICB Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 72

background image

4 Product Description

4.1 Product Description

4.1.1 General description

ICB pumps are single-stage volute casing pumps in block design. Hydraulic design and dimensions com-
ply with ISO 2858/ EN 22858, the technical design complies with ISO 5199/EN 25199.

The motors comply with DIN 42677-IM B5. Motor and pump shaft are coupled rigidly.

The permitted application conditions and design details of the delivered pump are shown in the attached
data sheet and / or the order confirmation (see

Design Coding System

below).

Installation position: ICB pumps are intended for use with horizontal shaft, discharge up. Installation posi-
tions deviating therefrom must be approved by the manufacturer.

Design Coding System

Due to the coding on data sheet and / or order confirmation all information regarding delivered pump can
be found in this Installation, Operation and Maintenance Instruction, e.g.:

ICB

100

- 65

- 250

S1

V

L

2

- 132

(0)

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

Table 4: Design coding system key

Position

Description

(0)

Name of Model

ICB - ISO block pump

(1)

Suction Nozzle mm | in

(2)

Discharge Nozzle in mm

(3)

Nominal diameter of impeller in mm

(4)

Shaft sealing

S1 - Single-mechanical seal acc. DIN 24960 l1k / EN 12756 form U

S4 - Single-mechanical seal acc. DIN 24960 l1k / EN 12756 form U with Quench (throttle bush)

(5)

Material Impeller

N = Cast Iron (0.6025)

L = Ductile Iron (0.7043)

V = Carbon Steel (1.4408) W = Duplex (1.4517)

(6)

Material pump casing (same coding as impeller, cast iron not available)

(7)

Stub shaft

2 - without shaft sleeve (Duplex 1.4462 std)

(8)

IEC Motor size

Mechanical seals

Pumps of design ICB are exclusively sealed with single mechanical seals with installation dimensions
acc. to EN 12756 (DIN 24960), design "K", form "U".

4 Product Description

ICB Installation, Operation and Maintenance Instruction

17

«
...
17
18
19
20
21
...
»

Содержание Goulds Pumps ICB









































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps ICB

VRV IV-S Series

Бренд: Daikin Страницы: 536

Бренд: Daikin Страницы: 226

Бренд: Xylem Страницы: 92

LOWARA e-SV Series

Бренд: Xylem Страницы: 48

Бренд: Calpeda Страницы: 72

LEADER ECOTRONIC Series

Бренд: DAB PUMPS Страницы: 10

Aeromax Piscine 10

Бренд: Thermor Страницы: 32

MULTI-HE Series

Бренд: salmson Страницы: 44

AJ 4 Plus 100/57 AUT

Бренд: T.I.P. Страницы: 20

Бренд: Daikin Страницы: 284

Бренд: D-D The Aquarium Solution Страницы: 18

Warren Rupp MARATHON M20

Бренд: Idex Страницы: 36

Бренд: Grundfos Страницы: 32

Бренд: Barmesa Pumps Страницы: 22

Бренд: Hi-Force Страницы: 8

Бренд: Rapid Страницы: 12

Бренд: Daikin Страницы: 57

GEOCLEAN FF02-V30

Бренд: Calpeda Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды