ITT Goulds Pumps ICB Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 72

background image

Additional connections

Any required sealing, flushing or cooling pipe connections must be installed. Please consult the data
sheet to see which pipes, pressures and amounts are necessary. The position and size of connections to
the pump are given in the appendix, "Connections".

NOTICE:

These connections are essential for the function.

It is recommended that a pipeline is installed to take off any leakage from the shaft seal. For connection,
see appendix, "Connections".

5.2.6 Additional connections

Any required sealing, flushing or cooling pipe connections must be installed. Please consult the data
sheet to see which pipes, pressures and amounts are necessary. The position and size of connections to
the pump are given in the appendix, "Connections".

NOTICE:

These connections are essential for the function!

It is recommended that a pipeline is installed to take off any leakage from the shaft seal. For connection,
see appendix, "Connections".

5.3 Drive

Note the Operating Instructions of the motor manufacturer.

On application in zone 1 and 2 a motor with valid Atex-certification must be used.

If in the process of the repair a new motor is used , the following has to be noticed:

•

The motor must comply with the requirements stated in sheet 1220.1A608 (order from manufactur-
er, on demand).

•

Clean motor end and motor flange of new motor carefully (remove varnish).

5.4 Final Control

It must be possible to turn the unit easily by hand at the stub shaft.

5.3 Drive

26

ICB Installation, Operation and Maintenance Instruction

«
...
26
27
28
29
30
...
»

Содержание Goulds Pumps ICB









































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps ICB

Бренд: OilGear Страницы: 28

Бренд: SAER Elettropompe Страницы: 76

Бренд: INOXPA Страницы: 20

POWERMASTER III

Бренд: Lincoln Страницы: 6

Бренд: Sicce Страницы: 24

TURBO-FLUX modular

Бренд: Cattani Страницы: 61

Бренд: OSO Страницы: 44

Бренд: Raypak Страницы: 57

Бренд: Yardworks Страницы: 19

Бренд: AMAZON COMMERCIAL Страницы: 48

Бренд: Wayne Страницы: 4

Little Giant PES-70

Бренд: Franklin Electric Страницы: 2

Бренд: Hamron Страницы: 19

Бренд: Rietschle Thomas Страницы: 48

POOLEX JETLINE SELECTION FI

Бренд: poolstar Страницы: 7

Бренд: Wilo Страницы: 32

Бренд: CLIVET Страницы: 56

Бренд: Danfoss Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды