ITT Goulds Pumps ICB Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 72

background image

NOTICE:

Pay attention to the utmost cleanness! Especially the seal faces must be clean, dry and un-
damaged. Don´t apply lubrication on the seal faces of the mechanical seal.

•

If a lubricant is provided with the replacement mechanical seal, you should use this.

NOTICE:

Use mineral grease or oil only, if you are completely sure that the elastomers of the mechanical
seal are oil resistant. Use no silicone.

NOTICE:

Use only lubricants when you are sure that there can´t occur any dangerous reactions between
the pumpage and the lubricant.

NOTICE:

Make all required parts available, so that assembly can be completed quickly. The lubricants
are only effective for a short time. After that the axial movability and, thus, the automatic adjust-
ment of the elastomeres is lost.

NOTICE:

Don´t push elastomers over sharp edges. If necessary use mounting devices.

•

Press the stationary part of the mechanical seal in the casing cover (161). For this you can eventu-
ally use a stamp with a soft surface. Unequal load can lead to cracking of the seal face.

•

Don´t damage seal face!

•

Pay attention that the stationary ring is in solid contact with the casing cover. The seal face must be
installed perpendicular to the shaft.

•

If a pin (560) is existing, be careful that it fits into the slot of the mechanical sealing, without touch-
ing the mechanical seal.

•

Push the rotating unit of the mechanical seal on the shaft (210).

•

Complete the face on the impeller side of the mechanical seal exactly with the shaft (measure l

1K

).

For mech. seals without own set screws the fixing ring (527) serves as a stop.

NOTICE:

Push mechanical seals with bellows in such a way, that the bellow is compressed and not
stretched (danger of tearing apart!).

•

Further mounting and installation of the pump referring to the repair instructions.

10.1 Single mech. seal without shaft sleeve (Design code S1..2)

50

ICB Installation, Operation and Maintenance Instruction

«
...
50
51
52
53
54
...
»

Содержание Goulds Pumps ICB









































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps ICB

Бренд: Gardena Страницы: 11

Бренд: Wanner Engineering Страницы: 16

Бренд: A.O. Smith Страницы: 8

Бренд: Danfoss Страницы: 26

Бренд: Calpeda Страницы: 80

Бренд: Danfoss Страницы: 24

Бренд: WACKER Group Страницы: 60

Бренд: A.O. Smith Страницы: 62

Xsential QUAD-RO

Бренд: Watermark Страницы: 8

Бренд: Becker Страницы: 5

Бренд: John Wood Страницы: 28

Бренд: Bard Страницы: 42

Бренд: Zodiac Страницы: 16

Бренд: Kawamoto Pump Страницы: 28

Бренд: Oase Страницы: 76

Бренд: O-SO Pure Страницы: 16

Бренд: KlimaTeknik Страницы: 16

Бренд: DROPSA Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды