ITT Goulds Pumps ICB Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 72

background image

1.4 General precautions

WARNING:

A pump is a pressure vessel with rotating parts that can be hazardous. Hazardous fluids may
be contained by the pump including high temperature, flammable, acidic, caustic, explosive,
and other risks. Operators and maintenance personnel must realize this and follow safety
measures. Personal injuries will result if procedures outlined in this manual are not followed.
ITT Goulds Pumps will not accept responsibility for physical injury, damage or delays caused
by a failure to observe the instructions in this manual and the IOM provided with your equip-
ment.

Table 1: General Precautions

WARNING

NEVER APPLY HEAT TO REMOVE IMPELLER. It may explode due to trapped liquid.

WARNING

NEVER use heat to disassemble pump due to risk of explosion from tapped liquid.

WARNING

NEVER operate pump without coupling guard correctly installed.

WARNING

NEVER run pump below recommended minimum flow when dry, or without prime.

WARNING

ALWAYS lock out power to the driver before performing pump maintenance.

WARNING

NEVER operate pump without safety devices installed.

WARNING

NEVER operate pump with discharge valve closed.

WARNING

NEVER operate pump with suction valve closed.

WARNING

DO NOT change service application without approval of an authorized ITT Goulds
Pumps representative.

WARNING

Safety Apparel:

•

Insulated work gloves when handling hot bearings or using bearing heater

•

Heavy work gloves when handling parts with sharp edges, especially impellers

•

Safety glasses (with side shields) for eye protection

•

Steel-toed shoes for foot protection when handling parts, heavy tools, etc.

•

Other personal protective equipment to protect against hazardous/toxic fluids

WARNING

Receiving:

Assembled pumping units and their components are heavy. Failure to properly lift and
support equipment can result in serious physical injury and/or equipment damage. Lift
equipment only at specifically identified lifting points or as instructed in the current IOM.
Current manuals are available at www.gouldspumps.com/literature_ioms.html or from
your local ITT Goulds Pumps sales representative. Note: Lifting devices (eyebolts,
slings, spreaders, etc.) must be rated, selected, and used for the entire load being lifted.

1.4 General precautions

ICB Installation, Operation and Maintenance Instruction

5

«
...
5
6
7
8
9
...
»

Содержание Goulds Pumps ICB









































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps ICB

Бренд: Davey Страницы: 12

Бренд: Barmesa Pumps Страницы: 42

Бренд: EAS Electric Страницы: 165

Бренд: ULTIMATE SPEED Страницы: 52

Бренд: Vagner Pool Страницы: 35

Бренд: A.O. Smith Страницы: 4

DURA-Power DRE-52

Бренд: A.O. Smith Страницы: 26

DURA-Power DRE-52

Бренд: A.O. Smith Страницы: 20

Altherma EKHWE150A3V3

Бренд: Daikin Страницы: 10

Бренд: EBARA Страницы: 48

Бренд: VONROC Страницы: 60

Бренд: Vallfirest Страницы: 32

Бренд: KlimaTeknik Страницы: 16

HOF14AFRQ 1F Series

Бренд: Halsey Taylor Страницы: 4

Бренд: Western Shelter Systems Страницы: 2

Бренд: Bard Страницы: 38

Бренд: WaterGroup Страницы: 24

Alaris CC Guardrails 80033UND1-G

Бренд: CareFusion Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды