ITT GOULDS PUMPS 3410 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 84

background image

housing to take any unbalanced axial thrust load. The radial bearing is free to float axially in the
bearing housing taking radial loads only.

•

Grease lubrication is standard. Oil lubrication is optional and uses the same shaft, bearings, and
bearing housings. Bearing cooling is available with oil lubrication only and is required for tempera-
tures over 121°C | 250°F. The bearing housings are completely sealed by Inpro VBS bearing isola-
tors.

Bedplates

Cast iron bedplates are furnished as standard. They include a drip collection chamber with a tapped
drain connection and an opening suitable for grouting. Fabricated steel bedplates are available as an op-
tion.

Intended applications

The Goulds 3410 model line is designed for a wide range of industrial, municipal, and marine services,
which includes:

•

Process – Quench water, stripper bottoms, reboiler circulation, and cooling tower

•

Pulp and paper – Primary and secondary cleaner, filtrate, mill water supply, and fan pump

•

Primary metals – Cooling water, quench, and leaching

•

Municipal – High lift, low lift, wash water, waste water, and raw water

•

Utilities – Cooling tower, component cooling, and service water

•

Marine – Bilge and ballast, cargo, cooling service, and fire pump

3.2 Nameplate information

Important information for ordering

Every pump has a nameplate that provides information about the pump. The nameplate is located on the
pump casing.

When you order spare parts, identify this pump information:

•

Model

•

Size

•

Serial number

•

Item numbers of the required parts

Item numbers can be found in the spare parts list.

Refer to the nameplate on the pump casing for most of the information. See Parts List for item numbers.

Nameplate types

Nameplate

Description

Pump casing

Pump

Provides information about the hydraulic characteristics of the pump.

The formula for the pump size is: Discharge x Suction - Nominal Maximum Impeller Diameter in
inches.

(Example: 2x3-8)

ATEX

If applicable, your pump unit might have an ATEX nameplate affixed to the pump, the base-
plate, or the discharge head. The nameplate provides information about the ATEX specifica-
tions of this pump.

3.2 Nameplate information

22

Model 3410 Installation, Operation, and Maintenance Manual

«
...
22
23
24
25
26
...
»

Содержание GOULDS PUMPS 3410





















































































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3410

Бренд: Bacharach Страницы: 12

Бренд: T.I.P. Страницы: 24

Бренд: Taco Страницы: 56

Бренд: Taco Страницы: 12

DURA-Power DRE-52

Бренд: A.O. Smith Страницы: 26

DURA-Power DRE-52

Бренд: A.O. Smith Страницы: 20

Бренд: Davey Страницы: 4

Бренд: Vagner Pool Страницы: 35

HELIFLOW 8 Series

Бренд: Gardner Denver Страницы: 64

Бренд: Waterax Страницы: 6

Бренд: SPERONI Страницы: 68

PC 3010 NT VARIO o.C.

Бренд: vacuubrand Страницы: 92

THBF701 Master Series

Бренд: bluefin Страницы: 17

Бренд: Newton Страницы: 4

AquaMax Eco Premium

Бренд: Oase Страницы: 380

Бренд: SUN HoM Страницы: 17

Бренд: HERBORNER pumpentechnik Страницы: 39

Бренд: Santon Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды