ITT GOULDS PUMPS 3410 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 84

background image

Brand

Lubricant type

Exxon

Teresstic EP 68

Mobil

DTE Heavy Medium

Phillips 66

Turbine Oil VG68

Shell

-29-0°C | -20-32°F: Tellus Oil 23

0-65°C | 32-150°F: Tellus Oil 68

65-93°C | 150-200°F: Turbo Oil 150

Royal Purple

SYNFILM ISO VG 68 Synthetic Oil

Texaco

Below 26.7°C | 80°F: Regal Oil R&O-46 #10 weight

Above 26.7°C | 80°F (): Regal Oil R&O-46 #20 weight

Dow Corning

High Vacuum Grease, NSF 61 compliant label

MOLYKOTE from Dow Corning 111, NSF 61 compliant label
Loctite

565 thread locker, NSF 61 compliant label

6.3.2.3 Lubricate new bearings with oil for the first time

New bearings should be lubricated as described in

5.8.2 Lubricate the bearings with oil (optional) on

.

6.3.3 Bearing temperatures

•

Bearing temperatures up to 82°C | 180°F are normal. For accurate measurement, place a contact-
type thermometer against the bearing housing. Record the reading in a convenient location for ref-
erence.

•

The stability of the temperature, rather than the number of degrees, is the best indication of normal
operation. A sudden increase in temperature is an indication of danger and a signal to investigate.
Check the unit for abnormal hydraulic operation and unnecessary loads, such as coupling misalign-
ment. See

7.1 Troubleshooting on page 74

•

Do not use the human hand as a thermometer. A temperature that feels hot to the hand can vary
from (49°C | 120°F to 54°C | 130°F depending upon the individual. Above this temperature, the hu-
man hand can not accurately estimate temperature.

6.3.4 Bearing conditions

The life of a bearing can be drastically reduced if contaminated with even a small amount of dust or dirt.
All bearing assembly operations must be done in an environment that is as free of dust as possible. All
tools and hands must be kept clean.

If...

Then...

New bearings need to be installed

They must not be unwrapped, cleaned, or washed until just before
the time of installation.

Old bearings are contaminated

They must be replaced. Washing bearings does not guarantee clean-
liness.

There is any question as to the condition of
bearings

It is always best to replace them. This may prevent an unplanned
shutdown. Check the bearing housing seals and replace as required.

6.3.4.1 Clean contaminated bearings

If new bearings are not available and immediate reassembly is necessary, then contaminated bearings
can be cleaned using the following procedure.

1.

Pour 1–2 quarts (0.9–1.9 liters) of clean, water-free kerosene into a clean pail.

2.

Dip the bearings into the kerosene and agitate slowly.

6.3 Bearing maintenance

58

Model 3410 Installation, Operation, and Maintenance Manual

«
...
58
59
60
61
62
...
»

Содержание GOULDS PUMPS 3410





















































































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3410

Бренд: Waters Страницы: 111

Бренд: Dantherm Страницы: 12

Бренд: DAXOM Страницы: 20

Бренд: Daikin Страницы: 40

Бренд: Rotex Страницы: 80

Бренд: Macnaught Страницы: 24

Бренд: Samoa Страницы: 4

Бренд: Xylem Страницы: 20

Бренд: Hamron Страницы: 19

Бренд: Rietschle Thomas Страницы: 48

Бренд: Wilo Страницы: 32

Бренд: Hubbell Страницы: 27

Бренд: Reliable Страницы: 18

Бренд: blupura Страницы: 28

Wilo-Sub TWU 3 HS Series

Бренд: Wilo Страницы: 192

OMNIA S HYBRID C 3.2

Бренд: Ferroli Страницы: 88

Бренд: Cornelius Страницы: 2

Бренд: Calorex Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды