ITT GOULDS PUMPS 3410 Скачать руководство пользователя страница 74

Страница: 74 / 84

Replace the cooling water piping.

Reinstall the drain plugs or close the drain valves.

Prime the pump.

Inspect after starting.

10. Check the stuffing boxes.

6.7.7 Bolt Torque Values - 3410 IOM

Table 4: Bolt Torque Values - FT-lb. (N-m)

Sizes

Dry Threads

Lub. Threads

Dry Threads

Lub. Threads

2210

2239

3/8"

12 (16)

6 (8)

36 (48)

18 (24)

7/16"

20 (28)

10 (14)

58 (78)

29 (39)

1/2"

30 (41)

15 (20)

90 (122)

44 (60)

9/16"

44 (60)

22 (30)

126 (170)

63 (85)

5/8"

60 (81)

30 (41)

175 (237)

87 (118)

3/4"

105 (142)

53 (72)

305 (414)

154 (209)

7/8"

170 (231)

85 (115)

495 (671)

248 (336)

255 (346)

128 (174)

740 (1003)

371 (503)

6.8 Spare parts

Critical service spare parts

ITT recommends that you have spare parts available to insure against possible long and costly downtime
periods, especially on critical services.

Part

Notes

Rotating element

This is a group of assembled parts including a shaft, impeller,
bearings, bearing housings with seals, wear rings, stuffing box
bushings, and all rotating parts except the coupling.

Stuffing box packing and lantern ring (if any)

One set for each stuffing box.

Mechanical seals (if any)

One seal for each stuffing box.

Recommended spare parts

Alternately, you can have the spare parts available that are most likely to wear and can be used as need-
ed.

Part

Notes

Stuffing box packing (if any)

One seal for each stuffing box.

Mechanical seal (if any)

Shaft sleeve (if any)

Ball bearings

One of each.

Wear rings

For the casing and the impeller.

Shaft

At least one is required.

Impeller key

Stuffing box bushings (if any)

6.8 Spare parts

Model 3410 Installation, Operation, and Maintenance Manual

Содержание GOULDS PUMPS 3410





















































































Результаты поиска

Содержание GOULDS PUMPS 3410

Отзывы:

Похожие инструкции для GOULDS PUMPS 3410

Бренды по названию

Популярные бренды

ITT GOULDS PUMPS 3410, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание GOULDS PUMPS 3410

Отзывы:

Похожие инструкции для GOULDS PUMPS 3410

Бренды по названию

Популярные бренды