ITT GOULDS PUMPS 3410 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 84

background image

CAUTION:

Failure to observe the instructions contained in this manual could result in personal injury
and/or property damage, and may void the warranty. Read this manual carefully before instal-
ling and using the product.

•

Never work alone.

•

Always wear protective clothing and hand protection.

•

Stay clear of suspended loads.

•

Always lift the product by its lifting device.

•

Beware of the risk of a sudden start if the product is used with an automatic level control.

•

Beware of the starting jerk, which can be powerful.

•

Rinse the components in water after you disassemble the pump.

•

Do not exceed the maximum working pressure of the pump.

•

Do not open any vent or drain valve or remove any plugs while the system is pressurized. Make
sure that the pump is isolated from the system and that pressure is relieved before you disassem-
ble the pump, remove plugs, or disconnect piping.

•

Never operate a pump without a properly installed coupling guard.

•

Always bear in mind the risk of drowning, electrical accidents, and burn injuries.

•

Never heat the condition monitor to temperatures in excess of 300°F (149°C).

•

Never expose the condition monitor to open flames.

•

Do not use the condition monitor in atmospheres containing acetic acid.

•

Always wear protective gloves. The pump and condition monitor can be hot.

1.5.3 Wash the skin and eyes

1.

Follow these procedures for chemicals or hazardous fluids that have come into contact with your
eyes or your skin:

Condition

Action

Chemicals or hazardous fluids
in eyes

1.

Hold your eyelids apart forcibly with your fingers.

2.

Rinse the eyes with eyewash or running water for at least 15 minutes.

3.

Seek medical attention.

Chemicals or hazardous fluids
on skin

1.

Remove contaminated clothing.

2.

Wash the skin with soap and water for at least 1 minute.

3.

Seek medical attention, if necessary.

1.6 Safety regulations for Ex-approved products in potentially
explosive atmospheres

Description of ATEX

The ATEX directives are a specification enforced in Europe for electrical and non-electrical equipment.
ATEX deals with the control of potentially explosive atmospheres and the standards of equipment and
protective systems used within these atmospheres. The relevance of the ATEX requirements is not limit-
ed to Europe. You can apply these guidelines to equipment installed in any potentially explosive atmos-
phere.

1.6 Safety regulations for Ex-approved products in potentially explosive atmospheres

8

Model 3410 Installation, Operation, and Maintenance Manual

«
...
8
9
10
11
12
...
»

Содержание GOULDS PUMPS 3410





















































































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3410

MRV II AV08NMVERA

Бренд: Haier Страницы: 40

FCD-JTHMG80-III

Бренд: Haier Страницы: 2

Little Sea-ox FCD-JTHC40-III (E)

Бренд: Haier Страницы: 6

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 23

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 2

Бренд: dafi Страницы: 12

Бренд: Walchem Страницы: 34

Бренд: WAGNER Страницы: 84

Бренд: WAGNER Страницы: 52

MiniTank WM-2.5

Бренд: Waiwela Страницы: 20

Бренд: Gude Страницы: 64

Бренд: Stübbe Страницы: 32

PVR50 Flanged Series

Бренд: Continental Hydraulics Страницы: 8

Бренд: salmson Страницы: 195

Бренд: Rinnai Страницы: 2

Бренд: Alpha Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды