ITT GOULDS PUMPS 3410 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 84

background image

5.20 Make the final alignment of the pump and driver

WARNING:

•

Failure to disconnect and lock out driver power may result in serious physical injury or
death. Always disconnect and lock out power to the driver before performing any installa-
tion or maintenance tasks.

•

Electrical connections must be made by certified electricians in compliance with all
international, national, state, and local rules.

•

Refer to driver/coupling/gear manufacturer's installation and operation manuals
(IOM) for specific instructions and recommendations.

•

Misalignment can cause decreased performance, equipment damage, and even cata-
strophic failure of frame-mounted units leading to serious injury. Proper alignment is the
responsibility of the installer and the user of the unit. Check the alignment of all drive
components prior to operating the unit.

•

Follow the coupling installation and operation procedures from the coupling manu-
facturer.

You must check the final alignment after the pump and driver are at operating temperature. For initial
alignment instructions, see the Installation chapter.

1.

Run the unit under actual operating conditions for enough time to bring the pump, driver, and asso-
ciated system to operating temperature.

2.

Shut down the pump and the driver.

3.

Remove the coupling guard.
See Remove the coupling guard in the Maintenance chapter.

4.

Check the alignment while the unit is still hot.
See Pump-to-driver alignment in the Installation chapter.

5.

Reinstall the coupling guard.

6.

Restart the pump and driver.

5.20 Make the final alignment of the pump and driver

Model 3410 Installation, Operation, and Maintenance Manual

53

«
...
53
54
55
56
57
...
»

Содержание GOULDS PUMPS 3410





















































































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3410

Little Sea-ox FCD-30

Бренд: Haier Страницы: 23

Бренд: Palm Страницы: 20

Бренд: Bard Страницы: 50

Бренд: Tebas Страницы: 14

Бренд: Radiant Страницы: 24

ROYTRONIC A Series

Бренд: LMI Страницы: 36

Бренд: AmeriWater Страницы: 16

American Pride ACNF Series

Бренд: Amana Страницы: 8

Бренд: Gorenje Tiki Страницы: 152

Бренд: Zoeller Страницы: 16

Бренд: STIEBEL ELTRON Страницы: 15

Flame Guard Safety System

Бренд: American Water Heater Страницы: 29

Бренд: B. Braun Страницы: 86

Бренд: Ranpump Страницы: 23

Бренд: American Standard Страницы: 2

BTN 120 THRU 400/A Series

Бренд: A.O. Smith Страницы: 32

Бренд: Hoval Страницы: 78

Бренд: Astralpool Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды