ITT GOULDS PUMPS 3410 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 84

background image

5.7 Couple the pump and driver

WARNING:

Failure to disconnect and lock out driver power may result in serious physical injury or death.
Always disconnect and lock out power to the driver before performing any installation or main-
tenance tasks.

•

Electrical connections must be made by certified electricians in compliance with all inter-
national, national, state, and local rules.

•

Refer to driver/coupling/gear manufacturer's installation and operation manuals (IOM) for
specific instructions and recommendations.

CAUTION:

•

The coupling guard used in an ATEX classified environment must be properly

certified and constructed from a spark resistant material.

•

Running a pump without safety devices exposes operators to risk of serious personal in-
jury or death. Never operate a unit unless appropriate safety devices (guards, etc.) are
properly installed.

Couplings must have proper certification to be used in an ATEX classified environment. Use

the instructions from the coupling manufacturer in order to lubricate and install the coupling. Refer to
driver/coupling/gear manufacturers IOM for specific instructions and recommendations.

5.8 Bearing lubrication

CAUTION:

•

Risk of explosive hazard and premature failure from sparks and heat genera-

tion. Ensure bearings are properly lubricated prior to startup.

•

Risk of heat generation, sparks and premature failure. Do not insulate bearing housings.

5.8.1 Lubricate the bearings with grease

Grease-lubricated pumps can be identified by grease fittings located on bearing housing. Sufficient lubri-
cant is inserted at the factory for 2,000 hours of operation. See the Maintenance chapter for grease lubri-
cation instructions.

5.7 Couple the pump and driver

Model 3410 Installation, Operation, and Maintenance Manual

43

«
...
43
44
45
46
47
...
»

Содержание GOULDS PUMPS 3410





















































































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3410

Бренд: Maag Страницы: 16

Бренд: A.O. Smith Страницы: 40

Бренд: WACKER Group Страницы: 60

Бренд: Watson-Marlow Страницы: 128

VRV IV-S Series

Бренд: Daikin Страницы: 536

Бренд: Daikin Страницы: 226

Бренд: Carrier Страницы: 12

Бренд: FUXTEC Страницы: 4

PULSAR Shadow Series

Бренд: Pulsafeeder Страницы: 46

Бренд: Wayne Страницы: 4

Бренд: Solar Energy Страницы: 4

Бренд: Carlisle Страницы: 24

Бренд: Realax Страницы: 60

Бренд: Biral Страницы: 104

Бренд: Goodman Страницы: 56

Бренд: Pfeiffer Vacuum Страницы: 64

Бренд: DAB Страницы: 52

ecoFIT pure 825

Бренд: Vaillant Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды