ITT GOULDS PUMPS 3410 Скачать руководство пользователя страница 8

Страница: 8 / 84

Electrical hazards are indicated by the following specific symbol:

ELECTRICAL HAZARD:

These are examples of other categories that can occur. They fall under the ordinary hazard levels and
may use complementing symbols:

•

Crush hazard

•

Cutting hazard

•

Arc flash hazard

1.3.1 The Ex symbol

The Ex symbol indicates safety regulations for Ex-approved products when used in atmospheres that are
potentially explosive or flammable.

1.4 Environmental safety

The work area

Always keep the station clean to avoid and/or discover emissions.

Waste and emissions regulations

Observe these safety regulations regarding waste and emissions:

•

Appropriately dispose of all waste.

•

Handle and dispose of the processed liquid in compliance with applicable environmental regula-
tions.

•

Clean up all spills in accordance with safety and environmental procedures.

•

Report all environmental emissions to the appropriate authorities.

WARNING:

If the product has been contaminated in any way, such as from toxic chemicals or nuclear radi-
ation, do NOT send the product to ITT until it has been properly decontaminated and advise
ITT of these conditions before returning.

Electrical installation

For electrical installation recycling requirements, consult your local electric utility.

1.4.1 Recycling guidelines

Always follow local laws and regulations regarding recycling.

1.4 Environmental safety

Model 3410 Installation, Operation, and Maintenance Manual

Содержание GOULDS PUMPS 3410





















































































Результаты поиска

Содержание GOULDS PUMPS 3410

Отзывы:

Похожие инструкции для GOULDS PUMPS 3410

Бренды по названию

Популярные бренды

ITT GOULDS PUMPS 3410, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание GOULDS PUMPS 3410

Отзывы:

Похожие инструкции для GOULDS PUMPS 3410

Бренды по названию

Популярные бренды