ITT Flygt 3102 Скачать руководство пользователя страница 27

Страница: 27 / 72

4. Refit the oil plug and tighten.

Tightening torque: 10-40 Nm (7.5-29.5 ft-lbs)

Disassemble the pump

Before the pump is disassembled the pump has to be drained of all coolant. For information, see

Empty the

oil

(page 23).

For specially approved drive units, follow the instructions in

Specially approved drive units

during the disassembly.

Follow the applicable instructions when removing the mechanical seal.

• Griploc seals:

Remove the inner mechanical seal: Griploc

(page 29)

• For seals type T, see information included in the spare part.
• Other seals:

Remove the mechanical seal

(page 27)

Remove the motor cable and the stator housing

(page 25)

Remove the pump housing

(page 26)

Remove the mechanical seal

(page 27)

Remove the outer mechanical seal: Griploc

(page 27)

Remove the outer mechanical seal

(page 27)

Remove the oil housing bottom

(page 28)

Remove the inner mechanical seal: Griploc

(page 29)

Remove the inner mechanical seal

(page 29)

Remove the bearings

Remove the stator from the stator housing

(page 30)

Remove the motor cable and the stator housing

1. Remove the stator housing:

a) Remove the stator housing screws.
b) Lift of the stator housing from the oil housing.

2. Open the entrance cover.

Maintenance (Continued)

Flygt 3102 Service and Repair Instructions

Содержание Flygt 3102









































































Результаты поиска

Содержание Flygt 3102

Отзывы:

Похожие инструкции для Flygt 3102

Бренды по названию

Популярные бренды

ITT Flygt 3102, Инструкции по обслуживанию и ремонту

Результаты поиска

Содержание Flygt 3102

Отзывы:

Похожие инструкции для Flygt 3102

Бренды по названию

Популярные бренды