ITT Flygt 3102 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 72

background image

Introduction and Safety

Introduction

Purpose of this manual

The purpose of this manual is to provide necessary information for:

• Installation
• Operation
• Maintenance

CAUTION:
Read this manual carefully before installing and using the product. Improper use of the product can cause
personal injury and damage to property, and may void the warranty.

NOTICE:
Save this manual for future reference, and keep it readily available at the location of the unit.

Transportation and Storage

For information about how to transport and store the pump, see Transportation and Storage in the
Installation, Operation and Maintenance manual.

Inspect the delivery

Inspect the package

1. Inspect the package for damaged or missing items upon delivery.
2. Note any damaged or missing items on the receipt and freight bill.
3. File a claim with the shipping company if anything is out of order.

If the product has been picked up at a distributor, make a claim directly to the distributor.

Inspect the unit

1. Remove packing materials from the product.

Dispose of all packing materials in accordance with local regulations.

2. Inspect the product to determine if any parts have been damaged or are missing.
3. If applicable, unfasten the product by removing any screws, bolts, or straps.

For your personal safety, be careful when you handle nails and straps.

4. Contact your sales representative if anything is out of order.

Product warranty

Coverage

ITT undertakes to remedy faults in products from ITT under these conditions:

• The faults are due to defects in design, materials, or workmanship.
• The faults are reported to an ITT representative within the warranty period.
• The product is used only under the conditions described in this manual.
• The monitoring equipment incorporated in the product is correctly connected and in use.
• All service and repair work is done by ITT-authorized personnel.
• Genuine ITT parts are used.
• Only Ex-approved spare parts and accessories authorized by ITT are used in Ex-approved products.

Introduction and Safety

Flygt 3102 Service and Repair Instructions

3

«
...
3
4
5
6
7
...
»

Содержание Flygt 3102









































































Отзывы:

Нет отзывов

Похожие инструкции для Flygt 3102

Бренд: Eaton Страницы: 2

Бренд: Salamander Pumps Страницы: 32

Бренд: Water Worker Страницы: 24

Бренд: DAXOM Страницы: 20

Бренд: German pool Страницы: 17

Бренд: A.O. Smith Страницы: 4

Бренд: Battery Watering Technologies Страницы: 2

NEXIS-VE Series

Бренд: salmson Страницы: 120

Бренд: EXTOL Страницы: 28

GPVX 75L Series

Бренд: A.O. Smith Страницы: 52

Бренд: Hi-Force Страницы: 16

Бренд: Ocean Aire Страницы: 36

Gusher 30 Series

Бренд: Whale Страницы: 8

Бренд: Alpha Страницы: 15

Бренд: Graco Страницы: 20

Бренд: American Water Heater Страницы: 24

Бренд: Dimplex Страницы: 24

VariAir VASF 2.50/X-1.AC115

Бренд: Becker Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды