ITT Flygt 3102 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 72

background image

Definitions

Safety message level

Indication

DANGER:

A hazardous situation which, if not avoided, will

result in death or serious injury

WARNING:

A hazardous situation which, if not avoided, could

result in death or serious injury

CAUTION:

A hazardous situation which, if not avoided, could

result in minor or moderate injury

Electrical Hazard:

The possibility of electrical risks if instructions are

not followed in a proper manner

NOTICE:

• A potential situation which, if not avoided,

could result in undesirable conditions

• A practice not related to personal injury

User safety

General safety rules

These safety rules apply:

• Always keep the work area clean.
• Pay attention to the risks presented by gas and vapors in the work area.
• Avoid all electrical dangers. Pay attention to the risks of electric shock or arc flash hazards.
• Always bear in mind the risk of drowning, electrical accidents, and burn injuries.

Safety equipment

Use safety equipment according to the company regulations. Use this safety equipment within the work area:

• Helmet
• Safety goggles, preferably with side shields
• Protective shoes
• Protective gloves
• Gas mask
• Hearing protection
• First-aid kit
• Safety devices

NOTICE:
Never operate a unit unless safety devices are installed. Also see specific information about safety
devices in other chapters of this manual.

Introduction and Safety (Continued)

Flygt 3102 Service and Repair Instructions

5

«
...
5
6
7
8
9
...
»

Содержание Flygt 3102









































































Отзывы:

Нет отзывов

Похожие инструкции для Flygt 3102

Бренд: Patterson Страницы: 16

Бренд: SAER Elettropompe Страницы: 36

Бренд: Vaillant Страницы: 40

Бренд: Valeo Страницы: 88

Бренд: Valdemar Energy Страницы: 61

Бренд: Zip Страницы: 16

Бренд: DAXOM Страницы: 20

Бренд: German pool Страницы: 17

Бренд: Edwards Страницы: 60

Бренд: SAER Elettropompe Страницы: 20

PAW-DHWM 80-120 ZNT

Бренд: Aquarea Страницы: 268

Бренд: Strom-Electrical Страницы: 8

Бренд: T.I.P. Страницы: 72

Бренд: WACKER Group Страницы: 60

Бренд: Grundfos Страницы: 28

Altherma 3 ECH2O

Бренд: Daikin Страницы: 68

Бренд: Carrier Страницы: 28

Smart Cylinders MS13555030S

Бренд: Rinnai Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды