ITT Flygt 3102 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 72

background image

Maintenance

Precautions

WARNING:

• Always follow safety guidelines when working on the pump. See

Introduction and Safety

(page 3).

• Disconnect and lock out electrical power before installing or servicing the pump.
• Make sure that the pump cannot roll or fall over and injure people or damage property.
• Rinse the pump thoroughly with clean water before working on the pump.
• Rinse the components in water after dismantling.

Make sure that you follow these requirements:

• Check the explosion risk before you weld or use electrical hand tools.
• Allow all system and pump components to cool before you handle them.
• Make sure that the product and its components have been thoroughly cleaned.
• Do not open any vent or drain valves or remove any plugs while the system is pressurized. Make sure

that the pump is isolated from the system and that pressure is relieved before you disassemble the
pump, remove plugs, or disconnect piping.

Maintenance guidelines

During maintenance and before reassembly, always remember to perform these tasks:

• Clean all parts thoroughly, particularly O-ring grooves.
• Change all O-rings, gaskets, and seal washers.
• Lubricate all springs, screws, and O-rings with grease.

During reassembly, always make sure that existing index markings are in line.
The reassembled drive unit must always be insulation-tested and the reassembled pump must always be test-
run before normal operation.

Torque values

Screw and nuts

Stainless steel, A2 and A4

Property

class

M4

M5

M6

M8

M10

M12

M16

M20

M24

M30

Torque,

Nm (ft-

lbs)

70 +80

1

2.7 (2)

5.4 (4)

9.3 (6.9) 22 (16)

44 (32)

76 (56)

187 (138) 364 (268) 629 (464) 1240

(915)

Carbon steel and alloyed steel

1

Property class 70 is torque tightened as class 80.

Maintenance

22

Flygt 3102 Service and Repair Instructions

«
...
22
23
24
25
26
...
»

Содержание Flygt 3102









































































Отзывы:

Нет отзывов

Похожие инструкции для Flygt 3102

Evosta2 11/139 SAN V

Бренд: DAB Страницы: 31

Бренд: DAB Страницы: 19

Бренд: GALAXY SPAS Страницы: 26

Бренд: Gardena Страницы: 16

Бренд: Gardena Страницы: 9

Бренд: Gardena Страницы: 11

13000 aquasensor

Бренд: Gardena Страницы: 14

Бренд: TDRFORCE Страницы: 12

Бренд: Raymarine Страницы: 24

SunCentric Series

Бренд: Dankoff Solar Страницы: 11

Бренд: Daewoo Страницы: 38

Бренд: Pentair Страницы: 36

Бренд: Daikin Страницы: 26

Бренд: PAPILLON Страницы: 16

Бренд: Oasis Aquatics Страницы: 14

Бренд: Barnes Страницы: 26

Бренд: Wilo Страницы: 19

Бренд: Reefe Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды