ITT Flygt 3102 Скачать руководство пользователя страница 60

Страница: 60 / 72

Service of the...

Action

Cable

1. If the outer jacket is damaged, replace the cable.
2. Check that the cables do not have any sharp bends and are not

pinched.

Connection to power

Check that the connections are properly tightened.

Electrical cabinets

Check that they are clean and dry.

Impeller

1. Check the impeller clearance.
2. Adjust the impeller, if necessary.

Stator housing

1. Drain all liquid, if any.
2. Check the resistance of the leakage sensor.

Normal value approx.1500 ohms, alarm approx. 430 ohms.

Insulation

1. Check that the resistance between the earth (ground) and

phase lead is more than 5 megohms.

2. Conduct a phase-to-phase resistance check.

Junction box

Check that it is clean and dry.

Lifting device

Check that local safety regulations are followed.

Lifting handle

1. Check the screws.
2. Check the condition of the lifting handle.
3. Replace if necessary.

O-rings

1. Replace the oil plug O-rings
2. Replace the O-rings at the entrance or junction cover.
3. Grease the new O-rings.

Overload protection and other

protections

Check the correct settings.

Personnel safety devices

Check the guard rails, covers, and other protections.

Rotation direction

Check the impeller rotation.

Oil housing

Fill with new oil, if necessary.

Terminal block/closed end splice Check that the connections are properly tightened.
Thermal contacts

Check the resistance of the leakage sensor.
Normally closed circuit; interval 0–1 ohm.

Voltage and amperage

Check the running values.

Major service

For a major service, take this action, in addition to the tasks listed under intermediate service.

Service of the...

Action

Support and main bearing

Replace the bearings with new bearings.

Mechanical seal

Replace with new seal units.

Service in case of alarm

For information about indication values for sensors, see

Sensor connection

Alarm source

Action

CLS

Check for water in the oil in the oil housing. If the oil contains to

much water:
1. Drain the oil and water.
2. Replace with new oil.

Maintenance (Continued)

Flygt 3102 Service and Repair Instructions

Содержание Flygt 3102









































































Результаты поиска

Содержание Flygt 3102

Отзывы:

Похожие инструкции для Flygt 3102

Бренды по названию

Популярные бренды

ITT Flygt 3102, Инструкции по обслуживанию и ремонту

Результаты поиска

Содержание Flygt 3102

Отзывы:

Похожие инструкции для Flygt 3102

Бренды по названию

Популярные бренды